English
Basic Settings
Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct
AUDIO/
position:TV/VCR 
To operate this receiver, set it to “AUDIO/TV/
CATV/DBS
VCR”
Recording a Source
For
You can record any analog source through the receiver to —
•the cassette deck (or MD recorder) connected to the TAPE/MD jacks,
•and the VCR connected to the VCR jacks
— at the same time.
For
You can record the currently selected digital input through the receiver to a digital recording device connected to the DIGITAL OUT terminal.
Notes:
•
•The output volume level, bass boost (see page 12), SEA modes (see page 24), and DSP modes (see page 25) cannot affect the recording.
•The test tone signal (see pages 29 and 30) does not come out through the DIGITAL OUT terminal.
Adjusting the Front Speaker Output
Balance
If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.
Changing the Source Name
When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.
On the front panel ONLY:
1. When changing the source name from “TAPE” to “MD”:
• Turn SOURCE SELECTOR until “TAPE” appears.
When changing the source name from “TV SOUND” to “DBS”:
•Turn SOURCE SELECTOR until “TV SOUND” appears.
2. Press and hold SOURCE NAME | BASS BOOST | |
| ||
(BASS BOOST) until “ASSGN. | SOURCENAME | |
MD” or “ASSGN. DBS” appears | ||
| ||
on the display. |
|
To change the source name to “TAPE” or “TV SOUND,” repeat
the same procedure above — in step 1, select “MD” or “DBS” then press and hold SOURCE NAME (BASS BOOST).
Note:
Without changing the source name, you can still use the connected components. However, there may be some inconvenience.
–“TAPE” or “TV SOUND” will appear on the display when you select the MD recorder or DBS tuner.
–You cannot use the digital input (see page 16) for the MD recorder.
–You cannot use the COMPU LINK remote control system (see page 39) to operate the MD recorder.
Before you start, remember...
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press BALANCE (/SURROUND) | BALANCE/SURROUND | ||
ADJUST repeatedly until “L/R |
| ADJUST | |
|
|
| |
BALANCE” appears on the display.
Setting the Subwoofer Information
Register whether or not you have connected a subwoofer.
Before you start, remember...
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
The display changes to show the current setting.
2. Turn MULTI JOG to adjust the | MULTI JOG |
balance. |
|
• Turning it clockwise decreases the left |
On the front panel ONLY:
1. Press SETTING repeatedly until “SUBWOOFER” appears on the display.
SETTING
channel output. |
• Turning it counterclockwise decreases the |
right channel output. |
The display changes to show the current setting.
MULTI JOG
2.Turn MULTI JOG to register whether you have connected a subwoofer or not.
•As you turn it, the subwoofer setting alternates between “YES” and “NO.”
YES: Select this when a subwoofer is used. SUBWFR lights up on the display (see page 11).
NO: Select this when no subwoofer is used.
13
