Digital Input (DIGITAL IN) Terminal Setting
When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3).
Before you start, remember...
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until | SETTING |
|
“DIGITAL IN” appears on the display.
The display changes to show the current setting.
DIGITAL 2 terminal setting
DIGITAL 1 terminal setting DIGITAL 3 terminal setting
MULTI JOG
2.Turn MULTI JOG to select the appropriate digital terminal setting.
• As you turn it, the display changes to show the following:
1 DVD 2 CD 3 TV (or DBS*) Ò
1 DVD 2 CD 3 MD Ò
1 DVD 2 MD 3 TV (or DBS*) Ò
1 CD 2 DVD 3 TV (or DBS*) Ò
1 CD 2 DVD 3 MD Ò
1 CD 2 MD 3 TV (or DBS*) Ò
1 TV (or DBS*) 2 CD 3 DVD Ò
1 TV (or DBS*) 2 CD 3 MD Ò
1 TV (or DBS*) 2 DVD 3 MD Ò
1 MD 2 CD 3 TV (or DBS*) Ò
1 MD 2 CD 3 DVD Ò
1 MD 2 DVD 3 TV (or DBS*) Ò (back to the beginning)
*If you have changed the source name from “TV SOUND” to “DBS,” “DBS” appears.
Note:
When shipped from the factory, the DIGITAL IN terminals can be used as the digital input for the following components.
•DIGITAL 1 (coaxial): For DVD player
•DIGITAL 2 (optical): For CD player
•DIGITAL 3 (optical): For digital TV broadcast tuner
Selecting the Analog or Digital Input
Mode
When you have connected some digital source components using the digital terminals (see page 8), you need to change the input mode for these components to the appropriate digital input mode correctly — AUTO/PCM, DOLBY DIGITAL, DTS, or MPEG.
Before you start, remember...
•The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.
On the front panel:
1. Turn SOURCE SELECTOR until | SOURCE SELECTOR |
the source (CD, MD, TV SOUND, |
|
DBS, or DVD)* for which you |
|
want to change the input mode |
|
appears on the display. |
|
Note:
*Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press INPUT ANALOG/DIGITAL | INPUT |
repeatedly until the digital input | ANALOG/DIGITAL |
| |
mode you want appears on the |
|
display. |
|
•Each time you press the button, the input mode changes as follows:
ANALOG |
| AUTO/PCM |
|
| (Digital) |
MPEG | DTS | DOLBY DIGITAL |
(Digital) | (Digital) | (Digital) |
Normally select “AUTO/PCM,” so the receiver automatically detects the incoming digital signal format. (The DIGITAL AUTO indicator lights up on the display.)
–When the receiver can recognize the digital signal format coming into the receiver, the frame of the digital signal indicator for the detected signal lights up automatically.
–When the receiver cannot recognize the incoming signal format correctly, the frame of the digital signal indicator flashes.
If this happens, select the same digital input mode with the incoming digital signal — either “DOLBY DIGITAL”, “DTS” or “MPEG.”
To change the input mode back to analog input, select
“ANALOG.”
From the remote control:
1. Press the source selecting button DVD DVD MUILTI | CD | TAPE/MD | |
(CD, TAPE/MD, TV/DBS, or | TV/DBS | PHONO | FM/AM |
|
|
|
DVD)* for which you want to | VCR |
change the input mode. |
|
Note:
*Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press ANALOG/DIGITAL to | ANALOG/DIGITAL |
change the input mode. |
|
•Each time you press the button, the input mode changes as follows:
ANALOG |
| AUTO/PCM |
|
| (Digital) |
MPEG | DTS | DOLBY DIGITAL |
(Digital) | (Digital) | (Digital) |
Notes:
•Noise may come out of the speakers while searching or skipping a
•When you change the source, the digital input mode will be automatically reset to “AUTO/PCM.”
English
16