JVC RX-7001PGD manual English, Adjusting the Surround Modes

English

3. Adjust the effect level.	BALANCE/SURROUND
1) Press (BALANCE/) SURROUND		ADJUST
ADJUST repeatedly until “DSP
EFFECT” appears on the display.
The display changes to show the current
setting.		MULTI JOG

2)Turn MULTI JOG to select the effect level.

•As you turn it, the effect level changes as follows:

DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5DSP EFFECT 4

As the number increases, the selected DAP mode becomes stronger.

From the remote control:

1. Press SURROUND MODE	SURROUND
repeatedly until the DAP mode —	MODE
LIVE CLUB, DANCE CLUB,
HALL, or PAVILION — appears
on the display.

The DSP indicator also lights up on the display.

•When you have set “REAR SPK” to “NONE,” the 3D- PHONIC indicator also lights up.

Adjusting the Surround Modes

Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.

Dolby, DTS and MPEG Surround adjustments

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 14).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•You cannot adjust the rear speaker output levels when you have set “REAR SPK” to “NONE.” See page 14.

•You cannot adjust the center speaker output level you have set “CENTER SPK” to “NONE.” See page 14.

From the remote control:

1. Press SURROUND ON/OFF to	SURROUND
activate an appropriate Surround	ON/OFF
mode — PRO LOGIC, DOLBY
DIGITAL, DTS SURROUND or
MPEG SURROUND.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the Ù PRO LOGIC indicator lights up on the display.

2. Press SOUND.

The 10 keys are activated for sound adjustments.

SOUND

Note:

You can also press SURROUND MODE to activate an appropriate

3. Adjust the speaker output levels.

• To adjust the left rear speaker level, press 5

REAR•L

6

Surround mode.

2. Press SOUND.

SOUND

REAR•L –/+ (from –10 dB to +10 dB).

•To adjust the right rear speaker level, press REAR•R –/+ (from –10 dB to +10 dB).

ENTER

REAR•R

The 10 keys are activated for sound adjustments.

3. Press TEST to check the speaker

output balance. TEST

8 9

4. Press EFFECT to select an effect

level you want.			EFFECT
			7/P
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1	DSP EFFECT 2		DSP EFFECT 3
DSP EFFECT 5		DSP EFFECT 4

As the number increases, the selected DAP mode becomes stronger.

“TEST TONE L” starts flashing on the					4
display, and a test tone comes out of the
speakers in the following order:
	TEST TONE L		TEST TONE C			TEST TONE R
	(Left front speaker)		(Center speaker)			(Right front speaker)
		TEST TONE LS		TEST TONE RS
		(Left rear speaker)		(Right rear speaker)

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CENTER SPK” is set to “NONE” (see page 14).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 14).

•If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.

25