English
2. Turn MULTI JOG to select the | MULTI JOG |
delay time of the rear speaker |
|
output.
•Turn it clockwise to increase the delay time from 0 msec (“R. DELAY: 0ms”) to
15 msec (“R. DELAY: 15ms”).
•Turn it counterclockwise to decrease the delay time from
15 msec (“R. DELAY: 15ms”) to 0 msec (“R. DELAY: 0ms”).
Notes:
•Rear delay time setting is not valid for the DVD MULTI playback mode.
•You cannot adjust the rear delay time when you have set “REAR SPK” to “NONE.”
Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocate the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).
To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected.
•If you have selected “LARGE” for all speakers (see page 14), this function is set to “OFF” and cannot be adjusted.
On the front panel ONLY:
1. Press SETTING repeatedly until | SETTING |
| |
“CROSSOVER FRQ” (Crossover |
|
Frequency) appears on the display. |
|
The display changes to show the current setting.
2. Turn MULTI JOG to select the | MULTI JOG |
| |
crossover frequency level |
|
according to the size of the small |
|
speaker connected. |
|
•As you turn it, the display changes to show the following:
80Hz
100Hz
120Hz
•Use the following comments as reference when adjusting.
80Hz: Select this when the cone speaker unit built in the speaker is about 12 cm.
100Hz: Select this when the cone speaker unit built in the speaker is about 10 cm.
120Hz: Select this when the cone speaker unit built in the speaker is about 8 cm.
Note:
Crossover frequency setting is not valid for the DVD MULTI playback mode,
Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using Dolby Digital, DTS Digital Surround or MPEG Multichannel follow the procedure below.
On the front panel ONLY:
1. Press SETTING repeatedly until | SETTING |
| |
“LFE ATT” (Low Frequency |
|
Effect Attenuator) appears on the |
|
display. |
|
The display changes to show the current setting. |
|
| MULTI JOG |
2.Turn MULTI JOG to select the low frequency effect attenuator level.
•As you turn it, the display changes to show the following:
0dB 
10dB
0dB: Normally select this.
10dB: Select this when the bass sound is distorted.
Note:
Low frequency effect attenuator setting is not valid for the DVD MULTI playback mode.
Dynamic Range Compression Setting
You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.
•This function takes effect only when playing back a source using Dolby Digital.
On the front panel ONLY:
1. Press SETTING repeatedly until | SETTING |
| |
“D. RANGE COMP.” (Dynamic |
|
Range Compression) appears on |
|
the display. |
|
The display changes to show the current setting. |
|
| MULTI JOG |
2.Turn MULTI JOG to select the appropriate item about the compression level.
• As you turn it, the display changes to show the following:
OFF 
MID
MAX
OFF: Select this when you want to enjoy surround with its full dynamic range. (No effect applied.)
MID: Select this when you want to reduce the dynamic range a little. (Factory setting.)
MAX: Select this when you want to apply the compression effect fully. (Useful at night.)
Note:
Dynamic Range Compression setting is not valid for the DTS Digital Surround, MPEG Multichannel and DVD MULTI playback mode.
15
