JVC RX-7040B, RX-7042S manual English, For DAP modes and Mono Film, Notes

For DAP modes and Mono Film

•Once you have made an adjustment, it is memorized for each mode.

EFFECT	Adjust the effect level. As the number
	increases, the effect becomes stronger.
	(Adjustable range: 1 to 5. “3” is the initial
	setting, and normally select this.)
ROOMSIZE	Adjust the virtual room size. As the number
	increases, the interval between reflections
	increases so that you will feel as if you were
	in a larger room.
	(Adjustable range: 1 to 5. “3” is the initial
	setting, and normally select this.)
LIVENESS	Adjust the liveness effect. As the number
	increases, the attenuation level of reflections
	over time decreases so that acoustics change
	from “Dead” to “Live.”
	(Adjustable range: 1 to 5. “3” is the initial
	setting, and normally select this.)

For Pro Logic II Music only

PNRM CNTRL Select “ON” to add “wraparound” sound effect with side-wall image. (Initial setting: “OFF.”)

CNTR WIDTH Adjust the center channel localization between the center speaker and the left/right front speakers. As the number increases, the center channel sound moves toward the left and right speakers. (Adjustable range: OFF and 1 to 7. “3” is the initial setting, and normally select this.)

DIMENSION Adjust the sound localization position. As the number increases, the sound localization moves towards forward from backward. (Adjustable range: 1 to 7. “4” is the initial setting, and normally select this.)

For Neo:6 Music only

CNTR GAIN Adjust the sound localization of the center channel. As the number increases, center channel will be localized clearly.

(Adjustable range: 0 to 0.5. “0.2” is the initial setting, and normally select this.)

You can also use the remote control for adjusting the speaker output level and center tone.

TEST	CENTER
	TONE
L FRONT R	CENTER

L SURR R S.BACK SUBWFR

To adjust the speaker output level:

1.Press TEST to check if you can hear the sounds through all the speakers at equal level.

Test tone comes out of the speakers in the following order.

•No test tone comes out of the speakers for which the speaker setting is set to “NONE” (or “NO” for the subwoofer).

FRNT L (Left front speaker) = CENTER (Center speaker) = FRNT R (Right front speaker) =

SURR R (Right surround speaker) = SBACK (surround back speaker) = SURR L (Left surround speaker) =

SUBWFR (Subwoofer) = (Back to the beginning)

2.Adjust the speaker output level.

Adjustable range: –10 dB to +10 dB. “0 (dB)” is the initial setting.

•To adjust the left front speaker, press FRONT L + or –.

•To adjust the center speaker, press CENTER + or –.

•To adjust the right front speaker, press FRONT R + or –.

•To adjust the right surround speaker, press SURR R + or –.

•To adjust the surround back speaker, press S.BACK + or –.

•To adjust the left surround speaker, press SURR L + or –.

•To adjust the subwoofer, press SUBWFR + or –.

Notes:

•When you press each button once, the current level for the selected speaker appears on the display, and the test tone comes out of the selected speaker.

•If no adjustment is done for about 4 seconds, the adjustment mode for the selected speaker is canceled.

•If you don’t have the test tone emitted, adjustment for the speaker output level is available. In this case, wait for about 4 seconds, after the adjustment is finished. Then the adjustment mode for the selected speaker is canceled and resumes the source indication on the display.

3.Repeat step 2 to adjust other speaker’s output levels.

4.Press TEST again to stop the test tone.

To adjust the center tone:

1.Press CENTER TONE repeatedly.

Adjustable range: 1 to 5. “3” is the initial setting, and normally select this.

2.Wait for about 4 seconds, after the adjustment is finished. The adjustment mode for the center tone is canceled and automatically resumes the source indication on the display.

English

29