English
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s components are preset in the remote control.
Operating Audio Components
IMPORTANT:
To operate JVC’s audio components using the supplied remote control:
•You need to connect JVC’s audio components through the COMPU LINK (SYNCHRO) jacks (see page 37) in addition to the connections using cables with RCA pin plugs (see page 9).
•Aim the remote control directly at the remote sensor on the receiver.
•If you use the buttons on the front panel to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selection buttons on the remote control.
•To operate the target component using the COMPU LINK remote control system, set the source name correctly if required. (See page 17.)
•Refer also to the manuals supplied with your components.
Sound control section (Amplifier)
You can always perform the following operations:
AUDIO: Turn on or off the receiver.
DIMMER:Dim or brighten the display.
VOLUME
MUTING:Turn on or off sound muting.
SURROUND: Turn on and select the Surround modes
DSP:Turn on and select the DSP modes.
SURR/DSP OFF: Turn off the Surround and DSP mode.
CCCONVERTER: Turn on or off CC Converter.
EX/ES:Select the EX/ES reproduction mode.
ANALOG DIRECT: Turn on or off Analog Direct.
ANALOG/DIGITAL INPUT:
Switch the analog and digital input alternately.
MIDNIGHT MODE: Select the Midnight Mode.
SLEEP:Set the Sleep Timer.
TEST:Turn on or off test tone output.
BASS BOOST: Turn on or off Bass Boost.
CENTER TONE: Adjust the center tone.
D.EQ FREQ: Select the frequency bands.
D.EQ LEVEL
FRONT L
FRONT R
CENTER
SURR L
SURR R
S.BACK
SUBWFR
Tuner
You can always perform the following operation:
FM/AM: Alternate between FM and AM.
After pressing FM/AM, you can perform the following operations on a tuner:
1 – 10, +10: Select a preset channel number directly. For channel number 5, press 5.
For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.
TUNING 9/(: Tune into stations.
FM MODE: Change the FM reception mode.
CD player
After pressing CD, you can perform the following operations on the CD player:
3: | Start playing. |
4: | Return to the beginning of the current (or previous) |
| track. |
¢: | Skip to the beginning of the next track. |
7: | Stop playing. |
8: | Pause playing. To resume, press 3. |
1 – 10, +10: Select a track number directly. For track number 5, press 5.
For track number 15, press +10, then 5. For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
CD changer
After pressing
3: | Start playing. |
4: | Return to the beginning of the current (or previous) |
| track. |
¢: | Skip to the beginning of the next track. |
7: | Stop playing. |
8: | Pause playing. To resume, press 3. |
1 – 6, 7/P: | Select the number of a disc installed in a CD |
| changer. |
After pressing CD, you can perform the following operations on a CD changer:
1 – 10, +10: Select a track number directly. For track number 5, press 5.
For track number 15, press +10, then 5. For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
Example:
•Selecting disc number 4, track number 12, and starting playback.
1.Press
2.Press CD, then press +10, 2.
If your CD changer is of
using the 10 keys after pressing CD.
1.Select a disc number.
2.Then select a track number (always enter two digits).
3.Press 3 to start playback.
Examples:
•Selecting disc number 3, track number 2, and starting playback. Press 3, then, 0, 2, then 3.
•Selecting disc number 10, track number 5, and starting playback. Press 1, 0, then, 0, 5, then 3.
•Selecting disc number 105, track number 12, and starting playback. Press 1, 0, 5, then 1, 2, then 3.
Note:
It is required to press each button within 4 seconds in the above procedure.
40
