JVC RX7030VBK manual Select a speaker you want to adjust

You can also use the remote control for adjusting the speaker output level.

When using the remote control, you can make an adjustment while listening to test tone.

1 2 3

4 5 6

7/P 8 9

10/0 0 +10

1.Press SOUND.

The 10 keys are activated for sound adjustments.

2.Press TEST to check if you can hear the sounds through all the speakers at equal level.

Test tone comes out of the speakers in the following order.

•No test tone comes out of the deactivated speakers and the subwoofer.

FRNT L (Left front speaker) = CENTER (Center speaker) = FRNT R (Right front speaker) =

SURR R (Right surround speaker) =

S BACK (surround back speaker) =

SURR L (Left surround speaker) = (Back to the beginning)

3.Select a speaker you want to adjust.

•To select the left front speaker, press FRONT•L.

•To select the center speaker, press CENTER.

•To select the right front speaker, press FRONT•R.

•To select the right surround speaker, press SURR•R.

•To select the surround back speaker, press SURR BACK.

•To select the left surround speaker, press SURR•L.

4.Press LEVEL + or LEVEL – to adjust the speaker output level (–10 dB to +10 dB).

5.Repeat steps 3 and 4 to adjust the other speaker’s output levels.

6.Press TEST again to stop the test tone.

Adjusting the Sound Parameters for the Surround and DSP Modes

You can adjust the Surround and DSP sound parameters to your preference.

•When center speaker is set to “NONE,” CTR TONE, CNTR WIDTH, and CNTR GAIN are not available.

7Adjustable parameters

You can adjust the following parameters:

For Surround, DAP, and All Channel Stereo modes (when the center speaker is connected)

•This setting is common to all surround modes, and is memorized separately for DSP modes.

CTR TONE: Adjust the center tone. As the number increases, the dialogue becomes clearer so that the human voices change from soft to sharp.

(Normally select “3 (initial setting).” Adjustable range: 1 to 5)

For DAP modes

•Once you have made an adjustment, it is memorized for each DAP mode.

EFFECT: Adjust the DAP effect level. As the number increases, the DAP effect becomes stronger. (Normally select “3 (initial setting).” Adjustable range: 1 to 5)

ROOMSIZE: Adjust the virtual room size. As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room.

(Normally select “3 (initial setting).” Adjustable range: 1 to 5)

LIVENESS: Adjust the liveness effect. As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.”

(Normally select “3 (initial setting).” Adjustable range: 1 to 5)

For Pro Logic II Music only

PANORAMA: Select “ON” to add “wraparound” sound effect with side-wall image. (Initial setting: “OFF”)

CNTR WIDTH: Adjust the center channel localization between the center speaker and the left/right speakers. As the number increases, the center channel sound moves toward the left and right speakers. (Normally select “3 (initial setting).” Adjustable range: OFF and 1 to 7)

DIMENSION: Adjust sound localization position. As the number increases, the sound localization moves towards forward from backward. (Normally select “4 (initial setting).” Adjustable range: 1 to 7)

For Neo:6 Music only

CNTR GAIN: Adjust the sound localization of the center channel. As the number increases, center channel will be localized clearly. (Normally select “0.2 (initial setting).” Adjustable range: 0 to 0.5)

English

33