ENGLISH

Connections

Before connecting this unit to the amplifier (or receiver), observe the following carefully.

•Turn off the amplifier.

•Make all connections before plugging in this unit.

•DO NOT connect this unit to the REC OUT jacks of your amplifier. It may damage your subwoofer.

Monaural audio cord (Supplied)

Amplifier or Receiver

To LINE OUT

To SUBWOOFER OUT

or MONO

 

To an AC outlet

SP-DWF10

SP-PWE5

To an AC outlet

Stereo audio cord (not Supplied)

In the case that the receiver dose not have the SUBWOOFER OUT or MONO terminal.

Operations

 

SP-PWE5 (Front)

SP-PWE5 (Rear)

SP-DWF10 (Front)

 

 

SP-DWF10 (Rear)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power lamp

Turning On the Power—POWER

To turn on the power.

Press the POWER switch to the [ ❙ or ] ON position.

• The power lamp lights in green.

SP-PWE5SP-DWF10

POWER

ON OFF

To cut of the power.

Press the POWER switch to the [ ‡ or ] OFF position.

•The power lamp goes out.

•This will disconnect the mains lead.

SP-PWE5SP-DWF10

POWER

ON OFF

Power lamp

Operating the Unit Automatically According to the Incoming Signals—AUTO POWER ON/STANDBY

To activate AUTO POWER ON/STANDBY.

Press the AUTO POWER ON/STANDBY switch to the [ ] ON position.

•If no sound comes in for 5-10 minutes, the unit enters standby mode. The power lamp lights in red.

•If the unit detects incoming signals, the unit starts operating. The power lamp lights in green.

To cancel AUTO POWER ON/STANDBY.

Press out the AUTO POWER ON/STANDBY switch to set it to the [ ] CANCEL position.

AUTO POWER ON / STANDBY

ON

CANCEL

When the volume level of the amplifier is so low or the incoming signals are so weak that this unit cannot detect sounds, Auto Power On/Standby may not work correctly.

– 8 –