Filename [DVM70S_10Timer Recording.fm]
Masterpage:Left+

46 EN TIMER RECORDING ON HDD/DVD DECK

Page 46Monday, 27 December 2004 14:08
You can programme this unit to timer-record as many as 16
programmes.
If you do not know the a number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
1Load a recordable disc if recording to DVD.
2Press PROGRAMME to access the programme top screen.
3Press FGD E to select ACALENDAR PR.B, then press ENTER.
When APROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMESB appears on the TV screen, you need to
cancel some of the reserved programmes. (Apg. 47)
4Press FGD E to select the desired date, then press ENTER.
5Press FG to select ARECORD
TOB, then press ENTER. Press
FG to select the desired
recording deck, then press
ENTER.
6Press FG to select ASTARTB,
then press ENTER. Press FG
to set the desired start time,
then press ENTER.
Each press of FG increases/decreases the start time in 1-
minute interval.
To increase/decrease the start time in 30-minutes interval,
press and hold FG.
7Press FG to select ASTOPB, then press ENTER. Press FG to
set the desired stop time, then press ENTER.
Each press of FG increases/decreases the stop time in 1-
minute interval.
To increase/decrease the stop time in 30-minutes interval,
press and hold FG.
8Press FG to select ATV PROGB, then press ENTER. Press
FG to select the desired channel.
9Press FG to select ACONFIRMB, then press ENTER.
10 Set the other recording options as required.
Refer to step 8 in Ab Timer ProgrammingB (Apg. 44).
11 Press FG to select AOKB,
then press ENTER to access
the Programme Confirmation
screen.
12 Press DE to select AEXITB,
then press ENTER to
complete timer
programming.
To programme another timer,
press DE to select ACONTINUEB, then press ENTER.
If APROGRAMME OVERLAPPEDB appears on the TV screen,
delete or modify the programmes.
NOTES:
When two successive programmes are recorded on a DVD-RW
disc with Manual Timer Programming function, the beginning of
the second one may be left off the recording.
If the copy limited programme is received during timer-recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.

Manual Timer Programming

Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
FGDE
PROGRAMME
ENTER
CABLE/SAT
DVDTV
BBC1
[MISC. ] XP
BBC1
23:00
22:30
HDD
2
PROGRAMME > CALENDAR PR. (2/3)
CONFIRM
14/01/04 WED 22:30 - 23:00
RECORD TO
STOP
START
TV PROG
ENTER
SELECT
PROGRAMME
EXIT
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
APerform AManual Timer ProgrammingB (Apg. 46).
In step 8, set ATV PROGB to AL-2B.
BSet the satellite receiver to the appropriate channel before
the selected programme begins.
CLeave the satellite receiver’s power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in XP mode.
If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
BBC1
1:00 28:00
2
ENTER
SELECT
PROGRAMME
EXIT
PROGRAMME > CALENDAR PR. (3/3)
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
OK
INPUT TITLE
CATEGORY
VPS/PDC
WEEKLY/DAILY
REC MODE
GARDENING
EDUCATION
OFF
MON-FRI (FOR A WEEK)
FR360
14/01/04 WED 22:30 - 23:00
GARDENING [EDUCATION] FR360
DVM70S_00.book Page 46 Monday, December 27, 2004 2:08 PM