Filename [DVM70S_12Editing.fm]
Masterpage:Left+

64 EN EDITING

Page 64 Monday, 27 December 2004 14:08
DECODER:
To use a decoder connected to the [L-2 IN/DECODER]
connector.
NOTES:
●If you have a satellite receiver or a decoder connected to the [L-2
IN/DECODER] connector, be sure to set AL-2 SELECTB back to
appropriate mode after editing.
●If you are not connecting a satellite receiver or a decoder to the
[L-2 IN/DECODER] connector, leave AL-2 SELECTB set to
AVIDEOB.
●When AL-2 SELECTB is set to ASAT VIDEOB and ASAT S-VIDEOB,
ASATB appears on the TV screen or front display panel instead of
AL-2B.
●If AL-1 OUTPUTB is set to ASCART S-VIDEOB, it is not possible to
set AL-2 SELECTB to ADECODERB or ASAT VIDEOB.
●If AL-1 OUTPUTB is set to ASCART RGBB, it is not possible to set
AL-2 SELECTB to ADECODERB or ASAT S-VIDEOB.
●If AL-1 OUTPUTB is set to ACOMPONENTB and AL-2 SELECTB to
ASAT VIDEOB, ASAT S-VIDEOB or ADECODERB, be sure to
connect the [L-1 IN/OUT] connector with a TV.
●If AL-2 SELECTB is set to ASAT S-VIDEOB, be sure to set AL-1
OUTPUTB to ASCART S-VIDEOB.
●The BNC and S-Video output do not support the satellite receiver
function. Make use of the L-1 output when viewing images from
the satellite receiver.

F-1 Input Setting

Set AF-1 INPUTB to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
1Perform steps 1 and 2 of AL-1 Output And L-1 Input SettingB
(Apg. 63).
2Press FG to select AF-1 INPUTB, then press ENTER.
3Press FG to select the
appropriate setting, then press
ENTER.
4Press SET UP to complete the
setting.
*The boldface settings below indicate the settings at your purchase.
8F-1 INPUT ^ VIDEO / S-VIDEO
VIDEO:
When connecting an appliance to the [VIDEO] input connector,
set to AVIDEOB.
S-VIDEO:
When connecting an appliance to the [S-VIDEO] input
connector, set to AS-VIDEOB.
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
Example: Dubbing to an MD
1Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
2Place a disc on the unit and load an MD on the connected
digital audio device.
3Select the audio to be dubbed.
4Start playback slightly before the actual point from where you
wish to start dubbing.
5Press W to pause playback.
6Select the input mode on the connected digital audio device.
7Press I to start playback on the unit.
8Start recording on the digital audio device.
9Stop recording on the digital audio device. Then press o to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
ENTER
SELECT
SET UP
EXIT
DVD VIDEO SET UP
MONITOR TYPE
HDD/DVD/DV SET UP
FUNCTION SET UP INITIAL SET UP
REC/PLAY SET UP DISPLAY SET
F-1 INPUT
L-1 INPUT
L-1 OUTPUT
L-2 SELECT
VIDEO IN/OUT
4:3LB
VIDEO
VIDEO
SCART VIDEO
VIDEO
VIDEO
VIDEO
S-VIDEO
SELECT WITH @ THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT

Digital Audio Dubbing

●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
Digital audio device
(MD deck, etc.)
Coaxial cable
(not supplied)
Player
Recorder
To [DIGITAL
AUDIO OUT
(COAXIAL)]
To [DIGITAL AUDIO
OUT (OPTICAL)]
Optical cable
(not supplied)
DVM70S_00.book Page 64 Monday, December 27, 2004 2:08 PM