JVC SR-MV50U manual Manual Timer Programming, Press PROG/CHECK to access the Program Check screen

				OPERATIONS ON DVD DECK EN 39
Manual Timer Programming				10 Press ENTER to access the Program Confirmation screen.
				11 Press ENTER to complete timer programming.
				● To program another timer, repeat steps 3 – 11.
				12 Press DVD TIMER (#) to engage the unit’s timer mode. The
				DVD timer indicator lights up on the front display panel and the
You can program this unit to timer record as many as 8 programs.				VCR deck is automatically selected. When the VCR deck is in
				timer standby mode, the unit is automatically turned off.
If you do not know the PlusCode number for the program you wish				#
to record, use the following procedure to set your unit to timer				● To disengage the timer mode, press DVD TIMER ( ) again.
				NOTES:
record the program.
				● When two successive programs are recorded on a DVD-RW disc
● Make sure that the unit’s built-in clock is set properly.				with Manual Timer programming function, the beginning of the
				second one may be left off the recording.
● Turn on the unit.
				● If the copy limited program is received during timer recording, the unit
● Turn on the TV and select the video channel (or AV mode).
				enters Record Pause mode. Recording starts again if it is switched to
● Slide the TV/CABLE/DBS/DVD switch to DVD.
				a recordable broadcast during the time you programmed.
				Cable Box and DBS Receiver Users
DVD TIMER (#)				To timer record a satellite broadcast using Manual Timer
VCR/DVD				Programming:
	1	2	3	A Perform “Manual Timer Programming” ( pg. 39).
	4	5	6
				B Set the cable box or DBS receiver to the appropriate channel
7	7	8	9
				before the selected program begins.
PROG/CHECK		0
				C Leave the cable box or DBS receiver’s power on.
ENTER			rtw e
				ATTENTION FOR DBS RECEIVER USERS
				If you are using a DBS receiver, the band indication (TV, CATV
				or DBS) appears on the left of the channel number indication.
				No indication: To timer record a regular TV broadcast received
				on the unit.
				CATV: To timer record a cable TV broadcast received on the unit,
				or through a cable box.
				DBS: To timer record a satellite broadcast received through a
				DBS receiver.
1 Load a recordable disc.				NOTE:
				If the channel number entered requires that the band be set,
2 Press VCR/DVD repeatedly so that the DVD lamp lights up on				“7=DBS” is displayed on the screen.
the unit.				If this happens, press the number key “7” to select “DBS”.

3 Press PROG/CHECK to access the Program Check screen.

●When “PROGRAM FULL DELETE

UNWANTED TIMER PROGRAM” appears on the TV screen, you need to cancel some of the reserved programs. ( pg. 42)

4 Press rt to select “NEW TIMER PROGRAM”, then press ENTER. The program screen appears.

5 Press rt to set the desired date.

● The current date appears on the TV screen. The date you enter appears in its place.

6 Press w e to select “START”, then press rt to set the desired start time.

●Each press of rt increases/decreases the start time in 1-minute interval.

●To increase/decrease the start time in 30-minutes interval, press and hold rt.

7 Press w e to select “STOP”, then press rt to set the desired stop time.

●Each press of rt increases/decreases the stop time in 1-minuteinterval.

●To increase/decrease the stop time in 30-minutes interval, press and hold rt.

8 Press w e to select “CH”, then press rt to select the desired channel.

●If you are using a DBS receiver, see “ATTENTION FOR DBS RECEIVER USERS” in the right column.

9 Set the other recording options as required.

●Refer to step 6 in “VCR Plus+® Timer Programming” ( pg. 38).