|
|
|
|
|
| EN 55 | |
|
|
|
|
|
|
| |
| TIMER RECORDING |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
|
| 1. | Timer recording will not work. |
| ● The clock and/or the timer have |
| Set the clock and/or timer correctly. |
|
|
|
|
| been set incorrectly. |
|
|
|
|
|
|
| ● The timer is not engaged. |
| Press TIMER and make sure that ä |
|
|
|
|
|
|
| appears on the front display panel. |
|
|
|
|
| ● The VCR has not been set up properly. |
|
| |
|
|
|
|
|
| Make sure you have compensated for |
|
|
|
|
|
|
| guide channel and VCR or cable box |
|
|
|
|
|
|
| channel number mismatches |
|
|
|
|
|
|
| (☞ pg. 30). |
|
|
|
|
|
|
|
|
|
| 2. | Timer programing will not work. |
| ● Timer recording is in progress. |
| Timer programing cannot be performed |
|
|
|
|
|
|
| when timer recording is in progress. |
|
|
|
|
|
|
| Wait until it finishes. |
|
|
|
|
|
|
|
|
|
| 3. | ä and ] on the front display |
| ● The timer is engaged but there is no |
| Load a cassette with the record safety |
|
|
| panel will not stop blinking. |
| cassette loaded. |
| tab intact. If the tab is removed, set |
|
|
|
|
|
|
| "REC SAFETY" to "OFF". (☞ pg. 37, |
|
|
|
|
|
|
| 41) |
|
|
|
|
| ● "REC SAFETY" is set to "ON" and the |
| Set "REC SAFETY" to "OFF" (☞ pg. |
|
|
|
|
| loaded cassette has had its record |
| 37, 41) or replace the cassette with |
|
|
|
|
| safety tab removed. |
| one on which the safety tab is intact. |
|
|
|
|
|
|
|
|
|
| 4. | ä blinks for 10 seconds and the |
| ● TIMER has been pressed when there |
| Check the programed data and set |
|
|
| timer mode is disengaged. |
| are no programs in memory, or the |
| again if necessary, then press TIMER |
|
|
|
|
| timer recording program has not |
| again. |
|
|
|
|
| been set correctly. |
|
|
|
|
|
|
|
|
|
|
|
| 5. | The power shuts off and ä and |
| ● The tape reaches its end during |
| The program may not have been |
|
|
| ] will not stop blinking. |
| timer recording. |
| recorded in its entirety. Next time be |
|
|
|
|
|
|
| sure you have enough time on the |
|
|
|
|
|
|
| tape to record the entire broadcast. |
|
|
|
|
|
|
|
|
|
| 6. | You moved, and now VCR Plus+ |
| ● The receivable stations in the new |
|
| |
|
| system does not work properly. |
| area are received on different |
| Setting procedure (☞ pg. 30). |
|
|
|
|
| channels than those in the previous |
|
|
|
|
|
|
| area. |
|
|
|
|
|
|
|
|
|
|
|
| 7. | “PROGRAM FULL” is displayed on |
| ● All 8 programs of the VCR’s timer |
| Wait until a space in memory clears, |
|
|
| the screen. |
| memory are used. |
| or cancel unnecessary program |
|
|
|
|
|
|
| information (☞ pg. 35). |
|
|
|
|
|
|
|
|
|
Page 55
Image 55
