JVC TK-C210FW manual Mounting the Camera to, Ceiling,  Connecting

Wrap insulation tape around cables.

Install the Ferrite core (TK-C210FW only) (A pg. 14)

5. Connect the input power supply cable. (A pg. 15)

6.

7.

8.

Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors.

Alarm signal cable (TK-C215V12 only)

5.7.

Solder or crimp

Insulation tape

Wrap with tape

8.

Input power supply cable

Connect the alarm cable. (TK-C215V12 only) (A pg. 15)

*TK-C215V4 is used in the above illustration

4. Connect the video signal cable. (A

Installation and connection (continued)

Mounting the Camera to the	6. Set the switches for video images.
	A

Installation and connection (continued)

 Mounting

Ceiling (continued)	(TK-C215V4 pg. 10)
	(TK-C215V12 A pg. 12)
	(TK-C210FW A pg. 14)

Adaptor ring

1. Align the position mark of the fastened

outer case with that of the camera unit.

When mounting the camera directly to the ceiling or on the wall

When mounting to a wall, replace areas indicated as “ceiling” in the procedures by “wall”.

Setup

1.Open a hole in the ceiling. (R30 mm)

Make use of the template supplied to open a hole.

2.Draw the fall prevention wire mounted to the ceiling slab and the cable out from the ceiling in advance.

CAUTION:

●Select a suitable safety cable based on length, strength, location, material (insulation property), etc.

●Use a ring on the fall prevention wire for mounting to the camera unit with an internal diameter of at least R3.1 mm or and not larger than R5.5 mm, and an external diameter that is not larger than R 9 mm.

3.Remove the dome cover.

As illustrated in the diagram, hold the dome ring such that the position mark comes between the thumb and index finger. Turn the ring in the anti-clockwise direction to remove.

3.

Dome Ring Position mark

4.Remove the outer case.

A Loosen the camera fastening screw with a screwdriver.

B To remove, turn the camera unit in the anti- clockwise direction.

A4.	5.
	Screw
	Pan fastening

6.

Camera

Fastening

Screw

C

4. B

*TK-C215V4 is used in the above illustration

Connecting

1.Align j with the shooting direction when mounting the cover to the ceiling.

Mount by using the supplied adapter ring to clamp between the outer case and the ceiling.

Notes on outer case mounting screws (not supplied):

●The diameter of the attachment hole of outer case is R4.5 mm (3/16 inch).

●Do not use flathead screws.

●When using an impact screwdriver, do not tighten the screws fully. Tighten using your hand instead. Failure to do so may damage the outer case.

2.Hang the fall prevention wire that has been dismantled in Step 4 C of the setup procedures to the hook.

3.Attach the fall prevention wire to the camera.

(Fall prevention wire is not included)

CAUTION:

● Tighten all screws securely. Otherwise the

1.

FRONTUP	Attach from
	the ceiling
	slab
Fall preven-	3.
tion wire
(not supplied)

4.

2.

Be sure to loosen the screw.

pg. 14)

NOTE:

When doing so, be careful not to catch the

cables in the outer case.

2. Turn the camera unit in the clockwise

direction.

T When doing so, ensure that the X mark is visible. (See illustration below)

3.Fasten the camera by tightening the camera fastening screw.

Position mark

1.	2.
	T Check

Camera fastening screw

3.

*TK-C215V4 is used in the above illustration

Adjusting Images

After mounting is completed, adjust the

images while checking the actual image. (A pg. 23 AAdjusting ImagesB)

C Dismantle the fall prevention wire.

5.Loosen the pan fastening screw.

CAUTION:

●Moving the lens unit without loosening the pan fastening screw may damage the lens unit.

camera may come loose and fall.

Protection cover

*TK-C215V12 is used in the above illustration

20 21