Introduction (continued)

Contents

 

Introduction

 

Safety Precautions

2

Characteristics

5

Contents

6

Operating Precautions

7

Name of Parts

8

Camera

8

Camera (Interior)

9

Setting the Lens and Switches

 

(TK-C215V4)

10

Setting the Lens and Switches

 

(TK-C215V12)

12

Setting the Lens and Switches

 

(TK-C210FW)

14

Installation and connection

 

About Connection Cables

14

Video signal cables

14

Installing the Ferrite core

 

(TK-C210FW only)

14

DC 12 V or AC 24 V power supply

 

cable

15

Electrical Specifications of Alarm Input

 

Terminals

15

System diagram

16

Mounting the Camera to the Ceiling

17

Getting Started

17

Selecting a mounting method

17

Embedding the camera to the ceiling

18

When mounting the camera directly to

 

the ceiling or on the wall

20

When mounting the camera to the

 

electrical box

22

Mount by allowing the cable to exit from

 

the side

22

Adjusting Image

 

Adjusting Images

23

Mounting the test monitor

23

Adjusting the camera direction

23

Adjusting the field angle/focus/

 

brightness

24

Mounting the Dome Cover

26

White-spot correction

27

Others

 

Specifications

28

Operating Precautions

To save energy, when it is not being used turn the system’s power off.

This camera has been designed for indoor use. It cannot be used outdoors.

Do not install or use the camera in the following places.

In a place exposed to rain or moisture.

In a place with vapor or oil soot, for example in a kitchen.

In a temperature outside the operating temperature range (-10 f to 50 f).

Near a source of radiation, X-rays, strong radio waves or magnetism.

In a place where corrosive gasses are generated.

In a place subject to vibration.

In a place with excessive dirt.

In an environment where there is cold air or near the air outlet of an air conditioner.

If this camera and the cables connected to this camera are used where there are strong electromagnetic waves or where there is magnetism present, for example near a radio or TV transmitter, power transformer or an electric motor, the picture may produce noise and the colors may be affected.

This camera incorporates an AGC circuit. As a result, when it is used under low light conditions, the camera sensitivity is automatically boosted and the picture may look uneven. This is not a malfunction however.

When this camera is used in the ATW mode, the recorded colors may be slightly different from the actual colors due to the operational principles of the auto-tracking white balance circuit. This is however not a malfunction.

If a high-intensity object (such as a lamp) is shot, the image on the screen may have vertical lines (smear) or blur (blooming) at its periphery. This is a characteristic of the CCD, and is not a defect.

Observe the following when carrying out camera maintenance.

Turn the power OFF before proceeding to carry out maintenance.

Clean the dome cover lens using a lens wiper cloth (or a tissue). If it is contaminated seriously, clean the contaminated part with a cloth (or a tissue) which has been soaked in a solution of water and a neutral detergent.

If the DAY/NIGHT switch is turned on, the mode changes automatically to black and white in dark places. As the sensitivity increases, the image may look grainy and white spots may appear.

When changing modes, bright portions of image may be emphasized but this is not a failure of the camera. (TK-C215V4/TK-C215V12 only)

When the supply voltage of the camera is low, the input protection circuit within the camera may be triggered and the power of the camera may turn off automatically. Make sure to use a supply voltage for the camera that is within -10 % of the rated voltage.

Upon switching between the HOME and ALARM positions, the camera focus may change slightly after the zoom operation comes to a stop. This is due to the built-in lens performance and is not a malfunction. (TK-C215V12 only)

When the camera is moved from a cold area to room temperature, condensation may occur causing the camera to malfunction as a result. In this case, turn on the power after waiting for a few hours.

This unit enlarges the rotation angle to support wide range set up.

For TK-C215V4 and TK-C215V12, when the zoom of the lens is set to WIDE end and the tilt angle is set around ±80 , the dome cover can be visible into the image depending on the rotation angle.

In this case, adjust the image angle if necessary. (A pg. 23)

All Interconnecting Equipment must be UL Listed.

Note on consumable parts (TK-C215V12 only)

The following parts are consumable and should be replaced after a certain number of hours or a count of operations. The service lives given below are only typical values. They may vary depending on the operating environment and conditions. Note that the replacement of consumable parts is chargeable even when they are replaced before the termination of the warranty period.

Zoom lens assembly

Zooming operation: 2 million times

6

7

Page 4
Image 4
JVC TK-C210FW manual Contents, Operating Precautions