JVC TK-C210FW manual  TK-C215V4 Adjusting the field angle/focus Brightness,  TK-C215V12

Adjusting Image (continued)

	 TK-C215V4
Adjusting the field angle/focus/
brightness				Iris Level
(Not available on TK-C210FW)			H	Adjustment
	L
		IRIS
Upon determining the imaging direction, adjust		LEVEL		Focus Adjust
the field angle, focus and iris level accordingly.				Button
			FOCUS ADJUST
The method of adjustment varies with the camera
in use.				Zoom ring

Adjusting Images (continued)

 TK-C215V12

● 2 types of angle of view may be selected for

TK-C215V12. In general, set in a way such

that the home position shoots a wide range

and the alarm position a narrow range.

‹Registering home position

For registering the angle of view during monitoring under normal conditions.

		H	R	B		RESET/[SPOT]
4.	IRIS	LEVEL
		L
2.,3.				8
				7
				6
			4	5
				4
	ZOOM/FOCUS FAR TELEWIDE	NEAR [MEMORY]	WHT.BAL.	3	PHASELL
			2	2

‹ TK-C215V4 (A pg. 24)

N F

● Use the alarm input mode selection switch to

set the actions when there is an alarm input.

(A pg. 13)

1. POSITION SELECT ALARM POSITION 1

‹ TK-C215V12 (A pg. 25)

Focus ring

W T

*TK-C215V4 is used in the above illustration

Adjusting field angle

Loosen the fastening screw for the zoom adjustment ring and move the ring to the left/right to adjust the image.

Adjusting focus

Press the FOCUS ADJUST button. The iris will be opened for 30 seconds. Loosen the fastening screw for the focus adjustment ring and move the ring to the left/right to align the focus.

NOTE:

● Set by repeating AAdjusting field angleB and AAdjusting focusB for 2 to 3 times. After adjustment is completed, fasten by tightening each of the fastening screws.

● The electronic shutter functions automatically upon pressing the focus adjustment button and the screen may flicker. However, this is not a malfunction.

Adjusting brightness

This adjustment only needs to be made when required. Use this to accommodate particular shooting conditions.

To darken image	: Counterclockwise (L side)
To brighten image	: Clockwise (H side)

NOTE:

● For adjusting the brightness, do not conduct it within 30 seconds after pressing the focus button.

● When adjusting the iris level, set the AGC switch to AOFFB. Otherwise, when the level is turned too far toward L, the AGC function activates increasing sensitivity and the picture may look uneven.

CAUTION:

●When setting images on TK-C215V12, ensure that the lens is covered using the dome cover. This camera is equipped with a high magnification lens. When adjustment is not performed through the cover, the lens may go out of focus when the cover is attached.

●When adjusting the focus, ensure that the optical axis of the lens and the center of the dome cover are aligned, and that the screen is not distorted. (See illustration below)

1.Check that the [ALARM POSITION] indicator light is turned off.

Registration of home position is enabled. Press the [POSITION SELECT] button if the [ALARM POSITION] indicator light is on.

2.Adjust the angle of view.

A Adjust the field angle

Move the zoom adjustment switch in the [TELE] or [WIDE] direction to adjust the field angle.

B Adjust the focus

Move the focus adjustment switch in the [NEAR] or [FAR] direction to adjust the focus.

NOTE:

When the [ZOOM/FOCUS] switch is set to either [TELE/WIDE] or [NEAR/FAR], the iris will automatically open up for about 30 seconds and focus can be easily adjusted. During this interval, the electronic shutter mode is activated and the image may flicker. However, this is not a malfunction.

3.Press the [MEMORY] button for 2 seconds or longer.

The [ALARM POSITION] indicator light blinks for 3 times (green)

4.Adjust the brightness.

This adjustment only needs to be made when required. Use this to accommodate particular

shooting conditions.

To darken image : Counterclockwise (L side)

To brighten image : Clockwise (H side)

NOTE:

●For adjusting the brightness, do not conduct it within 30 seconds after pressing the [ZOOM/ FOCUS] button.

●When adjusting the iris level, set the AGC switch to AOFFB. Otherwise, when the level is turned too far toward L, the AGC function activates increasing sensitivity and the picture may look uneven.



Home position registration is completed

24 25