JVC TM-H1950CG operating instructions HOW to USE the Menu, HOW to Initialize the Setting

1-10

HOW TO USE THE MENU

FUNCTIONS (cont’d)

Set-up menu items			Purpose			Settings
PICTURE SUB ADJ.		Image sub adjustment		Selects CONTRAST/BRIGHT/CHROMA/PHASE. The
					selected setting screen is shown. Select the function display for
					adjustment.
	CONTRAST	Adjusts contrast.			–10 –9 • • –01 00 +01 • • +09 +10

HOW TO INITIALIZE THE SETTING

SCREEN DISPLAY AND SELECTIONS IN THE <SET-UP MENU> RESET MODE

TM-H1950CG

No.

BRIGHT

Adjusts brightness.

–10

–9

• • –01

00

+01

• • +09

+10

CHROMA

Adjusts color density.

*1

–10

–9

• • –01

00

+01

• • +09

+10

PHASE

Adjusts hue.

*1

–10

–9

• • –01

00

+01

• • +09

+10

H. POSITION

Adjusts the horizontal position of the

screen (+: Horizontal position shifts

–5

• • • –01

00

+1

• • •

+5

to the right/-: Horizontal position shifts to

the left)

V. POSITION

Adjusts the vertical position of the screen

–5

• • • –01

00

+1

• • •

+5

(+: Vertical position moves up/-: Vertical

position moves down)

WHITE BALANCE

Adjusts the white balance.

Selects the drive (DRV) or cut off (CUTO) adjustment. The selected

setting screen is shown. Select the function display for adjustment.

DRIVE

R. DRIVE

Adjusts red level.

–20

– 19

• • –01

00

+01

• • +19

+20

B. DRIVE

Adjusts blue level.

–20

– 19

• • –01

00

+01

• • +19

+20

CUT OFF

R.

CUT OFF

Adjusts red cut off.

–20

– 19

• • –01

00

+

01

• •

+19

+20

G. CUT OFF

Adjusts green cut off.

–20

– 19

• • –01

00

+

01

• •

+19

+20

B. CUT OFF

Adjusts blue cut off.

–20

– 19

• • –01

00

+01

• • +19

+20

CONTROL LOCK

Sets the operation buttons on the front

OFF

ON

panel to control lock mode.

STATUS DISPLAY

Sets the status display of the color system.

OFF

ON

REMOTE SYSTEM

Sets the external control function method.

MAKE

TRG .

*2

INPUT REMOTE

Sets external control of input selection.

A – D

A/B

(Shown only when REMOTE SYSTEM is

*2

set to MAKE.)

You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and the volume level to their factory-set (initial) values.

1. Press the Power (			) switch to turn the power
OFF (activate the standby mode).
	POWER
2. While pressing both MENU button and				CHROMA/
PHASE button, press the Power (				) switch to turn
the power ON.
CHROMA	MENU	POWER	The <SET-UP MENU> RESET screen is displayed.
PHASE			Note:

●The <SET-UP MENU> RESET screen will not be displayed if the MENU or CHROMA/PHASE buttons are pressed for a very short time. Keep pressing them until the display screen appears.

<SET-UP MENU> RESET screen

<SET–UP MENU> RESET

Are you sure ? “Yes” then <+> “No” then <MENU>

Initial settings

Sorts	Functions (Items)		Initialization
			(setting)
	APERTURE	00
	ADJ. BAR POSI	LOWER
screen	COLOR TEMP	6500
	COLOR SYSTEM		AUTO
<MENU>	COMPO. LEVEL	00
	RUSH DELAY	STD.
	PICTURE SUB ADJ.
	CONTRAST	00
	BRIGHT	00
	CHROMA	00
	PHASE	00

ENGLISH

51961

*1 May not be shown depending on the type of signals input.

*2 Refer to HOW TO USE EXTERNAL CONTROL on page 18 for more details.

4.To set the other set-up menu items, repeat the procedures 2 and 3.

5.Press the MENU button to quit.

Front panel	Function	Contents
MENU	displayed
button

Notes:

● When the CONTROL LOCK function is

set to ON, pressing operation buttons

on the front panel will display the

message “CONTROL LOCK ON!” on

the screen for about 3 seconds.

● The CONTROL LOCK function is

maintained even when the power is

turned off.

● To turn off the CONTROL LOCK

function, while holding the MENU button

press the CHROMA/PHASE button.

Then set the CONTROL LOCK function

to OFF.

● Even when the CONTROL LOCK

function is set to ON, the following

3.Setting

Initialization is required.

VOLUME/SELECT	Press the VOLUME/SELECT [+] button.
	* Initialization is completed, and the <SET-UP MENU>
	RESET screen disappears.

Initialization is not required.

	H. POSITION		00
	V. POSITION		00
screen	WHITE BALANCE
	R. CUT OFF		00
	G. CUT OFF		00
MENU>
	B. CUT OFF		00
UP	R. DRIVE		00
<SET-	B. DRIVE		00
	CONTROL LOCK	OFF
	STATUS DISPLAY	ON
	REMOTE SYSTEM	MAKE
	INPUT REMOTE	A – D

		MENU	EXIT	Quit (or Release) the <MENU>
				screen
Note:
Setting	Description
MAKE	Make contact system: Controls the function using the control
	terminal’s short-circuit and open (short-circuits or opens 15th
	terminal (GND)).
TRG.	Trigger system: Controls the function by short-circuiting (short-
	circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
A-D	Switches the input by short-circuiting a specified signal line in
	INPUT A, B, C, or D.
A/B	Switches between INPUT A and INPUT B with D-sub pin 2.

operations are available:
–	Power Switch operation
–	Volume control with the VOLUME/
	SELECT buttons
–	Display or disappear of the <SET-UP
	MENU> screen.
● The STATUS DISPLAY function can be
set to display (ON) or not display (OFF)
the present color system when the
power is turned on or the input signal is
changed. Refer to page 9 for more
information.
● When REMOTE SYSTEM is set to
MAKE and any one of the INPUT A to D
buttons, the UNDER SCAN button,
COLOR OFF button or the ASPECT
button is pressed, “REMOTE ON!”
appears on screen for about 3 seconds.
(Not shown with CONTROL LOCK set
to ON.)
● When REMOTE SYSTEM is set to
TRG, the front panel controls can be
operated.
● INPUT REMOTE and REMOTE
SYSTEM are enabled when REMOTE
ENABLE is set to ON.

MENU

Press the MENU button.

* Initialization is aborted, and the <SET-UP MENU> RESET screen disappears.

	CHROMA	00
adjustment	PHASE	00
	CONTRAST	00
	BRIGHT	00
Picture
Volume	VOLUME	20

14 15