JVC UX-P450 manual 鐳射產品的重要說明

Warnings, Cautions and Others/ 警告，注意及其他須知事項

CAUTION—STANDBY/ON button!

Disconnect the mains plug to shut the power off completely (all lamps and indications go off). The STANDBY/ON button in any position does not disconnect the mains line.

•When the unit is on standby, the STANDBY/ON lamp lights in red.

•When the unit is turned on, the STANDBY/ON lamp lights in green.

The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

CAUTION

•Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

•Do not place any naked flame sources, such as lighted candles, on the apparatus.

•When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

•Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

注意 — STANDBY/ON 開關 !

無論 STANDBY/ON 開關在任何位置，電源線的電源還是 沒 有被切 斷，若要將 電源完 全關閉，應 把電 源插頭 拔离插 座 （所有的燈和信息均熄滅）。

•當主機正處于備用狀態， STANDBY/ON 燈為紅色。

•當主機開啟后，STANDBY/ON 燈為綠色。

電源開關可用遙控器控制。

注意

為了減少触電，火災等危險：

1.切勿擅自卸下螺絲釘，蓋子或機殼。

2.切勿讓本機受雨淋或置潮濕環境中。

注意

•切勿堵塞通風口或通風孔。

( 如果通風口或通風孔被報紙或布等堵塞，熱量將無法散 出。)

•切勿在本設備上放置任何裸露的火源，如點燃的蜡燭。

•處理廢棄電池時，必須考慮環境問題 ，并嚴格遵守當地關 于處理廢棄電池的有關法律或規定。

•切勿將本裝置暴露于雨水所及，潮濕 ，滴水或濺起水花的 地方，亦不要將任何裝滿液体的物件 ( 如花瓶 ) 放置在本 裝置上。

IMPORTANT FOR LASER PRODUCTS

1.CLASS 1 LASER PRODUCT

2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3.CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

鐳射產品的重要說明

1.一級鐳射產品。

2.注意：切勿打開頂蓋板。本机內部沒有用戶可自行維修的部 件；所有維修工作應由有資格的人員完成。

3.注意：當內部鎖定裝置失效或者損坏后，打開蓋板可能會產 生可見或不可見的鐳射輻射。應避免受到鐳射光束的直接照 射。

4.標簽的復制標示：注意標簽位于機內。

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1.Front: No obstructions and open spacing.

2.Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.

3.Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

15 cm	1 cm	15 cm	1 cm	15 cm
		15
15	1		1	15

10 cm 10

SP-UXP450 CA-UXP450 SP-UXP450

G-1

注意 : 正确通風

為免發生触電和火警的危險，及防止本機受損，請將本機如下 放置：

1.前面：沒有障礙物及地方開闊。

2.側面 / 頂面 / 背面：在圖中所示范圍中，不應放置任何障礙 物。

3.底部：放置在水平面上。放置在一個高 10 厘米或以上的臺 上，以保証足夠的通風道。

15 cm 15

15cm

15

CA-UXP450