Kenmore 10653552200, 10653272301, 10653272300, 2220694 manual Condition Setting Adjustment, Status

IMPORTANT:Becauseaircirculatesbetweenbothsections,any

odorsformedinonesectionwilltransfertotheotherYoumust.

thoroughlycleanbothsectionstoeliminateodorsToprevent.

odortransferfromfood,wraporcoverfoodstightly.

ElectronicControls(onsomemodels}

Foryourconvenience,yourcontrolsare preset at the factory,

When installing your refrigerator, make sure that the controls are still preset to the "mid-settings" as shown.

FREI_B{REFRI6ERATOR

OOOOOOO	OOOOOOO
1 = _ @ 5 0 7	i = _ @ s i 7

To turn on refrigerator:

•Press and hold ON/OFF for 2 seconds. The indicator lights show the current temperature control settings.

NOTE: Settings to the left of the mid-setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.

IMPORTANT:

•The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature.

•Wait 24 hours after you turn on the refrigerator before you put food into it. If you add food before the refrigerator has cooled completely, your food may spoil. Adjusting the Refrigerator and Freezer Controls to a colder setting will not cool the compartments any faster.

•If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked, before adjusting the controls.

•The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

Adjusting Electronic Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.

If you need to adjust temperatures:

•Press the FREEZER or REFRIGERATOR arrow to move the indicator light to the right, one setting at a time. Continue moving the indicator light until the desired setting is reached.

• o o	s 7 I
z

NOTE: With each press of the arrow, you will hear a beep as the light moves to the next setting. The indicator light moves to a setting of "7" and then returns to the setting of "1 ".

CONDITION:	SETTING ADJUSTMENT:
Refrigerator too cold	REFRIGERATOR	Control
- Not set correctly for	one setting lower
conditions
Refrigerator too warm	REFRIGERATOR	Control
- High use or room very warm	one setting higher
FREEZER too cold	FREEZER Control	one
- Not set correctly for	setting lower
conditions
Freezer too warm/too little ice	FREEZER Control	one
- High use or heavy ice usage	setting higher

Additional Electronic Control Panel Features

Additional features are located on the control panel at the top of the refrigerator compartment.

Water Filter Indicator Light and Reset

NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

The water filter display will help you know when to change your water filter cartridge. To change your filter, see the "Changing a Base Grille Filter" section.

INDICATOR:			STATUS:
GOOD	(green)		New filter installed
ORDER	(yellow)		Order filter, 10% filter life remains
REPLACE		(red) or when	Replace water filter
water flow		decreases

•After changing the water filter cartridge, reset the water filter indicator by pressing and holding the RESET for 2 seconds.

The status light will change from Replace (red) to Good

(green) when the system is reset,

_O

Accelerated Ice Production

The accelerated ice feature assists with temporary periods of heavy ice usage by increasing ice production over a 24-hour period.

•Press ICE touch pad to set the freezer temperature to -10°F (-23°C). The Accelerated Ice setting will remain on for 24 hours unless manually turned off.

If increased ice production is desired at all times, set the Freezer Control to a colder setting. Adjusting the freezer to a colder temperature may make some foods, such as ice cream, harder.

10