Review this chart to find
rized service representative,
......................................................i i iiiiiii
Disconnect electrical supply before servicing or cleaning the unit. Failure | I | |
WARNING | Electrical Shock Hazard | |
to do so could | result in electrical shock or personal injury, | |
, | i iii iii |
|
Cleaner | won't run. | 1. | Unplugged | at wall outlet |
| ||||
|
| 2, | Tripped | circuit | breaker/blown fuse | ||||
|
|
| at household | service panel | |||||
|
| 30ntOtf | switch | not turned | ON | ||||
|
| 4., | Thermal | protector tripped | |||||
Poor job | of dirt | 1. | Foil or clogged | dust bag |
| ||||
_}ck*up. |
| 2 | Wrong pile height setting |
| |||||
|
| 3_ | Worn | agffator |
|
|
| ||
|
| ; 4 | Clogged | nozzle | Or bag holder | ||||
|
| 5 | Clogged | hose |
|
|
| ||
|
| 6 | Hole | In hose |
|
|
| ||
|
| 7. | Hose | not inserted fully |
| ||||
|
| 8, | Motor | protection | system | activated | |||
|
| 9. | Dirty | fitters, |
|
|
|
| |
Cleaner | picks up | 1. | Wrong pile | he{ght setting |
| ||||
moveable rugs or |
|
|
|
|
|
|
|
| |
pushes | too hard, |
|
|
|
|
|
|
|
|
1Plug in firmly, push On/Off switch to
ON
2.Reset circuit breaker or replace fuse
3.Push On/Of! switch to ON
4o Allow vacuum to cool. then reset
Therma_ protector (page 12)
1, Change bag, (page 15) 2, Adjust setting, (page 7)
3, Take to your nearest Sears Service Center
4.Check CLOG REMOVAL, (page 18)
5.Check Ior clogs, (page t8)
6, Take to your nearest Sears Service Center
7, Insert hose fully, (page 10) 8, Check for clogs, (page !8) 9, Change fi_ters, (page 16).
I. Adjust setting, (page 7)
Light won't work, | 1 o | Burned | out | light bu}b | ||||
Agitator does | not turin | t_ | Agitator | On/Off | selector in | |||
|
|
|
|
| OFF pesilion |
| ||
|
|
|
| 2 | Handle | tn fu_l upright positron | ||
|
|
|
| 3 | Hose removed | fromnozzle | ||
|
|
|
| 4 | AgitatorOvedoad tripped | |||
|
|
|
| 5 | Thermal | protec{or tripped | ||
Performance |
| Indicator, | 1, | Futl or c$ogged dust bag | ||||
some models, | is | red. | 2_ | Dirty filters |
|
| ||
|
|
|
| 3 | Clogged | aidlow passage | ||
|
|
|
| 4, | Certain attachment tools | |||
Air flow restricted | 1. Attachment | use | restricts air flow | |||||
with attachment | use, |
|
|
|
|
| ||
Sound changes_ |
| 2, | New carpet | fuzz clogged air path | ||||
Dirt Sensor, | some | 1o | Dirty optic cells |
| ||||
models, will | not | work, |
|
|
|
|
|
I,,Change tight bulb, (page 17)
1.Move selector to the ON posit_on, (page 8)
2Move handto from upright position (page 7)
3Reattach hose to nozzle (page 10)
4Reset Agitator Over_oed (page 12)
5AJlow vacuum to cool, then reset Thermal protector (page 12).
I.Change bag, (page 15)
2,, Change fiJters, (page 16)
3.Clear clog from airflow passage, (page 18)
4,, This Is normal Light should go off when tool is removed
t.Check ATTACHMENTS, (page S)
2, Check CLOG REMOVAL end clean
hose, (page 18),
1.Clean optic cells, (page 13)
19