4.Remove the screw that secures the pilot shield and pilot assembly to the pilot bracket (Figure 35). Keep the screw for future use.

5.Loosen the nut securing the pilot tube to the pilot assembly. NOTE: To prevent any bending of the pilot bracket, use pliers to hold the pilot assembly bracket while loosening the pilot nut.

6.Pull the pilot tube from the pilot assembly (Figure 35).

IMPORTANT: Be careful not to bend or alter the position of the pilot assembly components.

7.Using the old pilot/pilot tube assembly as a guide, bend the new pilot tube to match the old one. NOTE: Make only the bends closest to the pilot before going to the next step. DO NOT crimp or crease the pilot tube.

8.Push the new pilot assembly connectors through the hole in the manifold door where the two piece wire connector wilt be seated (See Figure 35). Reconnect the pilot tube and tighten the nut securing it to the pilot assembly. IM PORTANT: Keep the pilot orifice in the pilot when making the connection. Do not operate the water heater without the pilot orifice installed.

9.Reattach the pilot shield and pilot assembly to the pilot bracket.

10.Reattach the burner and secure with the screws

removed earlier. NOTE: See Figure 34 for correct burner orientation.

11.Position the new pilot tube through the largest opening of the two piece wire connector. NOTE: The largest opening should be located at the top position. The igniter wire should be located in the middle opening and thermopile wires in the bottom opening.

12.Reposition the two piece wire connector in the manifold door opening and secure it with the retainer clip.

13.Before you proceed to the next step, install the new brass ferrule nut in the gas control valve/thermostat's pilot tube opening. HAND TIGHTEN ONLY.

14.See "Replacing the Manifold/Burner Assembly."

Burner and other fittings

not shown for clarity.

Thermopile

Connector

_tainer Clip

Wire

Pilot Tube _ _

Two Piece / _

Wire Connector

FIGURE 35.

Pilot

Thermopile

Thermopile

Connector

Thermal

Connectors

FIGURE 36.

Cleaning the Combustion Chamber and Flame-arrestor

1.Follow procedure outlined in "Removing the Manifold/ Burner Assembly."

2.Use a vacuum cleaner/shop vac to remove all loose debris in the combustion chamber (Figure 37). Use compressed

air to clear any dust or debris that may have accumulated in the flame-arrestor.

COMBUSTION CHAMBER

FLAME ARRESTOR

DOOR GASKET

BASE-RING

FIGURE 37.

3.Reassemble by following the procedure under "Replacing the Manifold/Burner Assembly."

Replacing the Manifold/Burner Assembly

Explosion Hazard

Tighten both manifold door screws securely.

Remove any fiberglass between gasket and combustion chamber.

Replace viewport if glass is missing or damaged.

Replace two piece wire connector if missing or removed.

Replace door gasket if damaged.

Failure to follow these instructions can result in death, explosion, or fire.

1.Check the door gasket for damage or imbedded debris prior to installation.

2.Inspect the view port for damage and replace as required.

3.Insert the manifold/burner assembly into the burner

31

Page 31
Image 31
Kenmore 153.331492, 153.331592 owner manual Cleaning the Combustion Chamber and Flame-arrestor, Explosion Hazard

153.331492, 153.331592 specifications

The Kenmore 153.331592 and 153.331492 are two innovative models in a series of versatile and efficient appliances designed to enhance everyday living. These products cater to a wide range of household needs, making them not only practical but also integral to modern home technology.

One of the standout features of the Kenmore 153.331592 is its energy efficiency. Designed with advanced technology, this model consumes less energy while providing robust performance. This is particularly important for environmentally conscious consumers looking to reduce their carbon footprint without compromising on effectiveness. The appliance utilizes smart energy management systems that optimize power use, ensuring that households can enjoy high performance with minimal energy costs.

On the other hand, the Kenmore 153.331492 offers impressive capacity, making it ideal for larger families or those who frequently entertain guests. This model is designed to accommodate substantial loads, whether it be laundry, cooking, or storage, making it a perfect fit for busy households. Additionally, its spacious design allows for easy organization, ensuring that items can be stored efficiently without clutter.

Both models incorporate advanced technology, including intuitive digital controls. These controls allow users to easily set preferences and monitor their appliance's operation through user-friendly interfaces. Smart connectivity features are also integrated into both models, allowing for remote management via smartphone apps. Users can adjust settings, receive alerts, and even perform diagnostics from the convenience of their phones, highlighting Kenmore's commitment to convenience and ease of use.

In terms of build quality, both models exhibit durable construction with high-quality materials designed to withstand the rigors of daily use. The sleek and modern design enhances their aesthetic appeal, making them suitable for any kitchen or laundry room decor.

Additionally, safety features such as auto shut-off, child locks, and overload protection are included in both models, ensuring that they operate smoothly without unnecessary risks.

In conclusion, the Kenmore 153.331592 and 153.331492 stand out for their blend of efficiency, capacity, and smart technology integration. These models present a compelling choice for those seeking reliable appliances that cater to both traditional and modern lifestyles. With a focus on energy conservation, user-friendly interfaces, and durable build quality, Kenmore continues to solidify its reputation as a leader in home appliance innovation.