OPERATION |
| OPERATION |
|
|
|
Always turn ON your hood before you begin cooking in order |
| Nigthlight switch |
to establish an air flow in the kitchen. Let the blower run for a |
| Press this switch once to turn on the nightlight. Press this switch |
few minutes to clear the air after you turn off the range. This |
| |
| once more to shut off the nightlight. | |
will help keep the whole kitchen cleaner and brighter. |
| |
|
|
Warranty
HC0027
1 | 2 |
| 3 | 4 | 5 |
1. Blower Delay switch |
| 4. Filter maintenance indicator | |||
2. ON/OFF Blower speed switches | 5. Nightlight switch | ||||
3. Halogen lights switch |
|
|
|
|
|
Delay OFF switch
When a speed is selected, press the Delay OFF switch to activate the delay function. The corresponding speed indicator LED will start flashing to indicate this function is activated. The fan will continue to operate for 5 minutes and will stop automatically. To cancel the delay function, press the Delay OFF switch once again; the blower will then work in normal mode.
NOTE: The blower speed can be increased or decreased during Delay mode without starting another
ON/OFF Blower speed switches
Press the switch corresponding to the desired blower speed. The light over the switch indicates the selected speed (from 1 for low speed to 4 for high speed). To turn off the blower, press once more on the corresponding blower speed switch.
HEAT SENTRY™
Your hood is equipped with a HEAT SENTRY thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface. The light indicator over speed 3 switch will quickly flash.
1)If blower is OFF - it turns blower ON to speed 3.
2)If blower is ON at a lower (or higher) speed setting - it turns blower to speed 3.
When the temperature level drops to normal, the blower will return to its original setting and the light indicator over speed 3 switch will stop flashing.
WARNING:The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF. 
When this occurs, press the speed 3 switch until its light indicator stops flashing if you must stop the blower.
Halogen lights switch
This switch provides 3 different lighting levels, according to your needs. The lighting intensity changes by increments of 1 (i.e.: press once for low intensity, once again to get more, up to three times). From the higher intensity, press once again to shut off the lights.
Uses 120 Volts, 50 W, MR 16 with GU10 base or PAR 16 with GU10 base, shielded halogen bulbs (included).
WARNING: In order to prevent the risk of personal injury, do not install a lamp identified 
for use only in enclosed fixtures.
Filter maintenance indicator
After 24 hours of operation, the filter maintenance light indicator will start blinking. This indicates the filters need to be cleaned in order to maintain efficient operation of the unit. The indicator light will blink until the function is reset by pressing the nightlight switch for 3 seconds.
CLEANING
Grease filters
The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe.
Wash more often if your cooking style generates greater grease - like frying foods or wok cooking.
Remove filters by pulling latch tabs and rotating filters downward.
Hood Cleaning
Stainless steel cleaning: How to maintain its “BRIGHT LOOK”
Do:
-Regularly wash surfaces with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent.
-Always clean in the direction of original polish lines.
-Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.
-You may also use a specialized household stainless steel cleaner.
Don’t:
-Do not use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.
-Do not use any harsh or abrasive cleaners.
-Do not allow dirt to accumulate.
-Do not let plaster dust or any other construction residues reach the hood. During construction/renovation, cover the hood to make sure no dust sticks to stainless steel surface.
Avoid: when choosing a detergent
-Any cleaners that contains bleach will attack stainless steel.
-Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
-Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should not be used close to a range.
3
Safety
Operation
Cleaning
Installation
Service Parts
