INSTALL THE HOOD
WARNING: When cutting or drilling into wall, do not damage electrical wiring and other 
hidden utilities.
1.Construct wood wall framing that is flush with surface of wall studs.
Wood wall framing must be at least 1/2” thick and 3” high. Ensure to assemble wood wall framing to wall studs for a solid installation.
Ensure the height of the framing will allow the mounting bracket to be secured to the framing within the dimensions shown (see illustration beside).
After wall surface is finished, carefully center and level the hood mounting bracket over installation location. Secure it to wall framing using 3 no. 8 x 1½” screws.
Using a level, draw a vertical line up to the ceiling starting from the mounting bracket center.
HD0374A |
36¾” = BOTTOM OF HOOD 24” ABOVE COOKTOP 42¾” = BOTTOM OF HOOD 30” ABOVE COOKTOP
Warranty
Safety
2. Center the upper flue mounting bracket with the center line |
|
|
|
| |
previously drawn and place it flush with the ceiling. | CEILING |
|
| ||
Use the upper flue mounting bracket as a template to mark |
|
| |||
|
|
|
| ||
the position of its screws. |
|
|
| Operation | |
Drill the 3 screw holes using a 3/16” drill bit. |
|
|
| ||
|
|
|
| ||
Insert the included drywall anchors into the drilled holes |
|
|
|
| |
(1 per hole). | HD0377 | L | MOUNTING BRACKET |
| |
Secure the upper flue bracket to the wall using 3 no. 8 x 3/4” |
| ||||
|
|
| C |
|
|
screws. |
| SCREW LOCATIONS | FLUSH WITH CEILING |
| |
Ensure that the bracket is tight against the wall. |
|
|
|
| |
! | WARNING: BE CAREFUL when installing the decorative flue and hood, they may have sharp edges. |
| |||
! | CAUTION: DO NOT REMOVE the protective plastic film covering the decorative flue (upper & lower). | Cleaning | |||
3. Align the hood and center it above the hood mounting |
| UPPER HOLES LOCATION | |||
bracket. Gently lower the hood until it securely engages the |
|
|
|
| |
bracket. |
|
|
|
| |
Level the hood. |
|
|
|
| |
With the hood hanging in place, secure it to the wall through |
|
|
|
| |
both holes located in the inside upper back of hood using |
| BACK OF THE HOOD |
| ||
2 no. 8 x 1½” screws. |
|
| |||
SIDE VIEW |
|
| |||
Drill through both holes located in the inside lower back |
|
| |||
|
|
|
| ||
of hood using a 3/16” drill bit. Insert the included drywall |
|
|
| Installation | |
anchors into the drilled holes (one for each hole). Secure |
|
|
| ||
|
|
|
| ||
the hood to the wall using 2 no. 8 x 3/4” screws and |
|
|
|
| |
2 washers. |
|
| Ø 3/16” TYP. |
| |
|
| HD0380A | LOWER HOLES LOCATION |
| |
HORIZONTAL DISCHARGE ONLY: | A |
| B |
| |
4. Position the blower on the higher (A) or lower (B) back wall |
|
| |||
|
|
|
| ||
discharge as determined previously. |
|
|
|
| |
Using a 5/16” socket, or a Robertson or a Phillips no. 2 |
|
|
|
| |
screwdriver and the 4 previously removed screws, secure |
|
|
|
| |
the blower to the hood. |
|
|
| Service | |
prepare the screw holes by screwing all 4 screws without |
|
|
| ||
NOTE |
| RIGHT SIDE |
|
| |
In order to ease installation, before mounting the blower, |
|
|
| ||
| MOUNTING |
|
| ||
|
|
|
|
| |
the blower, then remove and mount the blower. |
| SCREW |
| Parts | |
| LOCATION |
| |||
|
|
|
| ||
|
|
|
|
| |
5. Plug the blower back in and plug hood power cord into the | HD0387 |
|
|
| |
outlet. |
|
|
|
| |
|
| 11 |
|
|
|
