MANUALADVANCEREGENERATION CHECK

This check verifies proper operation of the valve motor, brine tank fill, brine draw, regeneration flow rates, and other controller functions, Always make the initial

checks, and the manual initiated diagnostics.

NOTE: The faceplate display must show a steady time (not flashing). If an error code shows, first press the SELECT1 button to enter the diagnostic display.

1.Press the REGENERATION button and hold in for 3 seconds. *RECHARGE and Fill begin to flash (or clean backwash begins, if set) as the softener enters the fill cycle of regeneration.

*NOTE: If the CLEAN feature is set to ON, a clean- ing backwash (CLEAN and Bkwsh or Rinse flashes in the display, along with the minutes of the clean cycle remaining), precedes the recharge.

2.When FILL is on steady, remove the brinewell cover

and, using a flashlight, observe fill water entering the tank.

3.If water does not enter the tank, look for an obstruct- ed nozzle, venturi, fill flow plug, brine tubing, or brine valve riser pipe.

CYCLE FLOW RATES (GALLONS PER MIN.)

FILL (flow to salt storage

tank)

0.3

(1.1

liters)

BRINING (flow

to drain)

 

.22 (.83

liters)

BRINE RINSE

(flow to drain)

.15 (.57

liters)

MAX. BACKWASH

(flow to drain)

2.0

(7.6

liters)

MAX. FAST RINSE

(flow

to drain)

2.0

(7.6

liters)

4.After observing fill, press the REGENERATION but- ton to move the softener into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level.

NOTE: Be sure a salt bridge is not preventing water with salt contact.

5.If the softener does not draw brine:

•nozzle and/or venturi dirty or defective.

•nozzle and venturi not seated properly on gasket

•restricted drain (check drain fitting and hose)

•defective nozzle and venturi seal

•other inner valve defect (rotor seal, rotor & disc, wave washer, etc.)

NOTE: If water system pressure is low, an elevated

drain hose may cause back pressure, stopping brine draw.

 

Brine Valve

 

Float Setting

m

 

q

 

_E j

Float Stop

S

Float

10"

p

FIG. 65

6.Again press REGENERATION to move the softener into backwash. Look for a fast flow of water from the

drain hose.

7.An obstructed flow indicates a plugged top distributor, backwash flow plug or drain hose.

8.Press REGENERATION to move the softener into fast rinse. Again look for a fast drain flow. Allow the softener to rinse for a few minutes to flush out any brine that may remain in the resin tank from the brin- ing cycle test.

9.To return the softener to service, press REGENERA- TION once more.

Questions? Call The Kenmore Water Line 1-800-426-9345

38

Page 37 Page 39
Page 38
Image 38
Kenmore 625.38376 owner manual Manualadvanceregeneration Check, Checks, and the manual initiated diagnostics, Brine Valve
Page 37 Page 39

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents