Kenmore 630.1391 Dry Assist, Cycle Completion Signal select models, Changing A Cycle, drying

	OPTIONS				CYCLE SELECT	START
9Hr.®				®	@
6Hr. O	Smart	Pots &	NormaU	China	Fast
	•	®	o	Gentb	Wash
3Hr.®	Wash z/s	Pans	Wash
Delay	Turbo					CA_CE,
Start	Clean					.OLO3S_C

If your unit has a display similar to the one shown above, follow the instructions below.

CANCELING A CYCLE

*Open the door.

*Hold down the CANCEL button until the "WASHING" LED goes out. Close the door.

*Wait for about 1 minute until the dishwasher drains.

*The "COMPLETE" LED will illuminate. This indicates that the unit has been reset.

CHANGING A CYCLE

If you need to change the running cycle to a new cycle:

*Open the door.

*Hold down the CANCEL button until the "WASHING" LED goes out.

*Wait for about 1 minute until the dishwasher drains.

*The "COMPLETE" LED will illuminate. This indicates that the unit has been reset.

*Press "POWER" button to turn the unit off. Then press the "POWER" button again to turn the unit back on.

*You can now select a new cycle.

To enter the options mode: (rinse aid setting, dry assist)

*Door must be open. Press the "POWER" button to turn the unit on.

*One of the wash cycle LEDs will be flashing.

*Press and hold the ">" button, then press and release the "START" button. Now release the ">" button.

*The "Sanitized" and one other LED will be flashing. You are now in the options setup mode.

*Press ">" to select the option you would like to adiust.

If the "COMPLETE" and "RINSE AID" LEDs are flashing, you are in the "Rinse Aid" mode. You can adiust the amount of Rinse Aid dispensed.

If the "COMPLETE" and "SANITIZED" LEDs are flashing, you are in the "Dry Assist" mode. You can now activate or deactivate Dry Assist.

If the "COMPLETE", "SANITIZED", and "RINSE AID" LEDs are flashing, you are in the "Cycle Completion Signal" mode. You can now increase or decrease the tone or deactivate the signal.

To set the amount of Rinse Aid:

NOTE: if your glasses have spots on them, you need more rinse agent. If your glasses have streaks, you need less Rinse Agent.

Follow the instructions to enter "options" mode. With the "COMPLETE" and "RINSE AID" LEDs flashing :

*Press the "<" button to change the amount of rinse agent dispensed.

0 LEDs lit --_ rinse aid dispenser is OFF

1LED lit --_ Lowest amount of rinse aid dispensed

2 LEDs lit --_ Medium amount of rinse aid dispensed 3 LEDs lit --_ Highest amount of rinse aid dispensed Press "START" to save your settings.

Dry Assist

With this option you can raise the temperature of the rinse water and increase the drying time for improved

drying.

Follow the instructions to enter "options" mode. With the "COMPLETE" and "SANITIZED" LEDs flashing:

Press the "<" button to activate or deactivate dry assist. 0 LEDs lit --_ extra dry heat is OFF

1 LED lit --_ extra dry heat is ON Press "START" to save your settings.

Cycle Completion Signal (select models)

The cycle completion signal alerts you when a cycle completes and the dishwasher has washed and dried the dishes. You can choose to disable the tone or adiust the volume.

Follow the instructions to enter "options" mode. With the "COMPLETE" and "RINSE AID" LEDs flashing:

Press the "<" button to adiust or deactivate the cycle completion signal.

0 LEDs lit -_ cycle completion signal is OFF 1 LED lit -_ Lowest tone level

2 LEDs lit -_ Medium tone level

3 LEDs lit -_ Highest tone level Press "START" to save your settings.

Time Delay

This option allows you to delay the start time of your cycle. To activate:

Turn the dishwasher on.

Select the desired wash cycle.

Press the Delay Start button until the desired delay time illuminates in the "3Hr", "6Hr", "9Hr" LED.

Press "START" to save your settings.

16