Drain hose, Dispenser | Kenmore 630.13959, 630.13952, 630.13953

Drain hose

COMPONENTS

Drain hose

Dishwashers use a two-hose (internal / external) drain hose system. A customer (external) drain hose (during installation) is connected to the internal drain hose, with the 90º elbow pointing toward the customer drain. The external drain hose connects directly to the customer drain system without an adapter.

Dispenser

The dispenser is located near the top of the inner door and reliably dispenses detergent and rinse-aid.

During each wash program, the wax motor opens twice, once to dispense detergent and again to dispense rinse-aid. The wax motor opens the same -- linkages open the detergent door & operate the rinse-aid dosage plunger. Dispensers can have reed switches or optical rinse-aid sensors.

CAUTION: Inner door edges are sharp! Cover door edges and remove dispenser carefully.

The white plastic linkage opens the detergent dispenser door, then cocks in place to dispense rinse-aid when the wax motor operates again. After the 2nd operation, the linkage resets for the next wash.

702_58300000149896_ara_en_b

Image 21

Kenmore 630.13959, 630.13952, 630.13953 manual Drain hose, Dispenser

Contents

Sears Brands Management Corporation KENMORE ELITE DISHWASHERSHoffman Estates, IL 60179 U.S.A Toronto, Ontario, Canada M5B 2C3 TECHNICAL SPECIFICATIONS FAULT DIAGNOSTICSWIRING DIAGRAMS COMPONENTS SAFETY I. SAFETYIA. General hazards m IB. Electrical shock / fire hazards c h INSTALLATION II. INSTALLATIONIIA. Pre-Installchecklist IIB. Alignment IIC. Electrical connection IIE. Drain and condensation hose connections INSTALLATION IID. Water connection III. OPERATION Reset “Cancel – Reset”Sanitized and Refill Rinse Agent lights Dry Assist The End of cycle tone volume can be changed Changing basic featuresEnd of cycle tone IIIC. Entering special programs and coding PX Program codes EX Error codesP4 = Control coding see CX control codes CX Control codes Preparing a dishwasher for showroom use Preparing a showroom dishwasher for resaleWARNING: Danger of electrical shock Adjusting rinse-aiddosage DispenserClosing dispenser doors Tank IV.COMPONENTSHeater Operation Heater ratings Leveling feet front and rear Water switchMicroswitch Cam Disk Circulation pumps BLDCFloat Solving installation issues Pump specificationsDrain pump Cavitating Johnson Tee installations Washington State Terminal connections Rast 5 connectorsWater fill assembly Siphoning Flowmeter Using hinge slider sliding pulley Condensation tubeDoor spring Water inlet valve Hinge bushing Door latch On/off switchTerminal block Terminal box Drain hose Optical rinse-aidsensors Aqua sensor Display and power modulesPower module Control module Sump parts SumpBackflow check valve Info lights Spray arm feed tube Water circulation Operation Understanding the 17-digitserial # Serial label warranty information To remove outer door V. RepairTools needed: T20 Torx screwdriver To remove toe kick To flip dishwasher upside-down Tools needed: T20 Torx screwdriver and pliers To raise block up right side of tank To remove water valve For access to circulation pumpTools needed: T20 Torx screwdriver & pliers Connection hints Tools needed: flat blade screwdriver To remove complete pumpFascia panel mounted controls Tools needed: T-20Torx & flat blade screwdrivers Base mounted controls To access base-mountedcontrolsTools needed: T-20Torx screwdriver & pliers 1.Remove outer door – see section VA For access to heaters & NTC’s To remove heater, NTC & flow switchVE. Heaters 4.Push NTC latches and lift NTC from heater Softer bearing heaters 1.Remove outer door --section VA To remove dispensersRepair VF. 2-piecedrain hose connection VG. Drain pumps To remove door latches 1.Remove fascia panel --section VDVI. Door latches Misaligned door latches Entering customer service test program VI.Fault DiagnosticsFault Diagnostics VIA. Customer service test program Clearing error codes Error code displays Symbol Viewing customer service program Fault Dishwasher troubleshootingFailure Resolution Steps to determine failure Dispenser Will not fill Heater diagnosingor does not fill with Controls timing out and showing “1” Heating system checklist if controls time out Where to measure NTC resistances NTC resistance chart Cosmetic / Customer Use / Installation Issues Checklist if water leaks past doorsWater Leaking Past Doors Not cleaning or locking sump filters Customer self-helpdiagnosing VII. Technical Specifications Technical SpecificationsUnsatisfactory washing results Wiring Diagrams VIII. Wiring Diagrams 702_58300000149896_ara_en_b Wiring Diagrams