To flip dishwasher upside-down

Repair

Tools needed: T20 Torx screwdriver, Phillips screwdriver and pliers.

1.Turn off water and electricity. Disconnect dishwasher mounting brackets (1).

2.Remove toe kick by removing two Phillips screws and tilting toe kick out from dishwasher (2).

3.Disconnect water line and electric supply (3).

4.Pull dishwasher out, place a pad or cardboard on the floor and carefully flip the dishwasher upside-down (4).

5.Remove four base screws from front of dishwasher (5).

6.Remove two screws securing water valve to base. There’s no need to disconnect valve wire harness or inlet hoses (6).

7.Pull wire harness connector from rear of terminal box (7).

8.Push latch on base-mounted control to disconnect it from base (8).

9.Remove both door springs from base (9).

10.Remove two tank screws from rear of dishwasher (10), disconnect both rubber circulation pump supports (11) and carefully lift up base from dishwasher (12).

702_58300000149896_ara_en_b

Page 29

Image 29

Kenmore 630.13953, 630.13959, 630.13952 manual To flip dishwasher upside-down

Contents

Sears Brands Management Corporation KENMORE ELITE DISHWASHERSHoffman Estates, IL 60179 U.S.A Toronto, Ontario, Canada M5B 2C3 TECHNICAL SPECIFICATIONS FAULT DIAGNOSTICSWIRING DIAGRAMS COMPONENTS SAFETY I. SAFETYIA. General hazards m IB. Electrical shock / fire hazards c h INSTALLATION II. INSTALLATIONIIA. Pre-Installchecklist IIB. Alignment IIC. Electrical connection IIE. Drain and condensation hose connections INSTALLATION IID. Water connection III. OPERATION Reset “Cancel – Reset”Sanitized and Refill Rinse Agent lights Dry Assist The End of cycle tone volume can be changed Changing basic featuresEnd of cycle tone IIIC. Entering special programs and coding PX Program codes EX Error codesP4 = Control coding see CX control codes CX Control codes WARNING: Danger of electrical shock Preparing a dishwasher for showroom usePreparing a showroom dishwasher for resale Closing dispenser doors Adjusting rinse-aiddosageDispenser Tank IV.COMPONENTSHeater Operation Heater ratings Leveling feet front and rear Water switchMicroswitch Cam Disk Float Circulation pumpsBLDC Solving installation issues Pump specificationsDrain pump Cavitating Johnson Tee installations Washington State Terminal connections Rast 5 connectorsWater fill assembly Siphoning Flowmeter Door spring Using hinge slider sliding pulleyCondensation tube Water inlet valve Hinge bushing Door latch On/off switchTerminal block Terminal box Drain hose Optical rinse-aidsensors Aqua sensor Display and power modulesPower module Control module Backflow check valve Sump partsSump Info lights Spray arm feed tube Water circulation Operation Understanding the 17-digitserial # Serial label warranty information To remove outer door V. RepairTools needed: T20 Torx screwdriver To remove toe kick To flip dishwasher upside-down Tools needed: T20 Torx screwdriver and pliers To raise block up right side of tank To remove water valve For access to circulation pumpTools needed: T20 Torx screwdriver & pliers Connection hints Tools needed: flat blade screwdriver To remove complete pumpFascia panel mounted controls Tools needed: T-20Torx & flat blade screwdrivers Base mounted controls To access base-mountedcontrolsTools needed: T-20Torx screwdriver & pliers 1.Remove outer door – see section VA VE. Heaters For access to heaters & NTC’sTo remove heater, NTC & flow switch 4.Push NTC latches and lift NTC from heater Softer bearing heaters 1.Remove outer door --section VA To remove dispensersRepair VF. 2-piecedrain hose connection VG. Drain pumps VI. Door latches To remove door latches1.Remove fascia panel --section VD Misaligned door latches Entering customer service test program VI.Fault DiagnosticsFault Diagnostics VIA. Customer service test program Clearing error codes Error code displays Symbol Viewing customer service program Fault Dishwasher troubleshootingFailure Resolution Steps to determine failure Dispenser Will not fill Heater diagnosingor does not fill with Controls timing out and showing “1” Heating system checklist if controls time out Where to measure NTC resistances NTC resistance chart Cosmetic / Customer Use / Installation Issues Checklist if water leaks past doorsWater Leaking Past Doors Not cleaning or locking sump filters Customer self-helpdiagnosing Unsatisfactory washing results VII. Technical SpecificationsTechnical Specifications Wiring Diagrams VIII. Wiring Diagrams 702_58300000149896_ara_en_b Wiring Diagrams