Troubleshooting
Please review this troubleshooting chart prior to calling for service.
PROBLEMS |
|
| SOLUTIONS |
|
|
|
|
| |||||
Dishes | do not dry |
| The rinse aid dispenser may | be empty. Check the | |||||||||
|
|
|
|
|
| necessary. Dishware drying can be accelerated and enhanced by opening the | |||||||
|
|
|
|
|
| dishwasher door slightly and propping it open with the top rack. |
| ||||||
Indicator | light(s) | do not | A fuse may have | blown or a circuit | breaker tripped. Check the fuse or circuit | breaker | |||||||
come on |
|
|
|
| at your fuse box/breaker box and | replace | the fuse or reset the breaker if necessary. | ||||||
Dishwasher | does | not | The dishwasher | door may not be properly | shut. Make certain the dishwasher | door is | |||||||
start |
|
|
|
|
| shut and latched. |
|
|
|
|
| ||
Dishwasher | runs | a long | If the dishwasher | completes | the cycle, but the run time seems exceptionally | long, it | |||||||
time |
|
|
|
|
| may be due to cold incoming | water. Before starting the dishwasher, open the hot | ||||||
|
|
|
|
|
| water faucet at the sink nearest the dishwasher. Run the water until it runs hot, then | |||||||
|
|
|
|
|
| turn off the water and start the dishwasher. |
|
| |||||
Machine | cycle | does not | NOTE: The Installation Manual that came | with your dishwasher will help you with the | |||||||||
advance | to | rinse |
| following | instructions. |
|
|
|
| ||||
|
|
|
|
|
| The water supply line may be shut off. Check the water supply valve and open it if it's | |||||||
|
|
|
|
|
| shut. Or, the water inlet may be blocked. Using the Installation Manual that came with | |||||||
|
|
|
|
|
| your dishwasher as a guide, shut off the dishwasher's water supply, remove the | |||||||
|
|
|
|
|
| dishwasher's toe panel, water supply hose or tubing, and 90 ° elbow, and look for | |||||||
|
|
|
|
|
| debris in the water inlet. If debris is present, try removing it with tweezers. Then, | |||||||
|
|
|
|
|
| return the 90 ° elbow, water supply hose or tubing, and toe panel to their installed | |||||||
|
|
|
|
|
| positions, and open the dishwasher water supply. |
| ||||||
Water | not pumped from | Make certain the drain hose isn'tkinked, clogged, or improperly installed. Make | |||||||||||
dishwasher |
|
|
| certain a portion | of the drain | hose is at least 20 inches above the dishwasher's | |||||||
|
|
|
|
|
| enclosure floor (see the Installation Manual). Filters may be clogged. Make certain the | |||||||
|
|
|
|
|
| filter system isn'tclogged (see the Care and Maintenance section of this manual). | |||||||
|
|
|
|
|
| The kitchen sink drain may be clogged; you may need a plumber rather than a | |||||||
|
|
|
|
|
| serviceman for the dishwasher. If an air gap is installed at sink, it may be clogged. | |||||||
Detergent | dispenser | You may | not be correctly shutting | the detergent dispenser cover, or a cycle was not | |||||||||
cover | will not | shut | finished | and should be cancelled. Go to the Adding Detergent and Rinse Aid section of | |||||||||
|
|
|
|
|
| this manual for instructions on shutting the detergent dispenser cover. Go to the | |||||||
|
|
|
|
|
| Operating the Dishwasher section of this manual for instructions on cancelling a | |||||||
|
|
|
|
|
| cycle. |
|
|
|
|
|
|
|
White | spots left on | More rinse aid is needed. Go to the Adding Detergent and Rinse Aid section | of this | ||||||||||
dishes |
|
|
|
|
| manual for instructions on increasing the amount of rinse aid dispensed. |
| ||||||
Streaks on | glassware | Too much | rinse aid is being dispensed. Go to the Adding Detergent and Rinse Aid | ||||||||||
|
|
|
|
|
| section of this manual for instructions on decreasing the amount of rinse aid |
| ||||||
|
|
|
|
|
| dispensed. |
|
|
|
|
|
| |
Rattling noises |
| Utensils | may not be properly | arranged. |
|
| |||||||
Suds in dishwasher | You may have used the wrong type of dishwasher detergent. Use only automatic | ||||||||||||
|
|
|
|
|
| dishwasher | detergents. |
|
|
|
| ||
Unsatisfactory | washing | • Incorrect | amount of detergent. |
|
|
| |||||||
results |
|
|
|
|
| • Utensils | incorrectly arranged or rack overloaded. |
|
•Spray arm rotation blocked by utensils.
•Spray arm nozzles need cleaning.
•Filters not properly fitted into position.
•Unsuitable cycle selected.
Troubleshooting | 15 |