Kenwood VR-2000 Conec the, system control, cord.,ayeri.ecordp,ayer1, System Controloperations

Conec the system control :9

Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations.

There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below.

[_] Mode :lets you corrlbine [_. _(_8]. and _ termina s 1"_1]El Mode : for [__]E_] terminals only

This unt is compatible with both [X58} and ISL161 modes. It comes from the factory set to the [SL16] mode To switch to the [XS81 mode, fellow

the instructions in "SWITCHING FROM [SL161 TO [XS8]" below.

EXAMPLE:	[xsa]	mode connections	EXAMPLE:	[XS16] mode connections
			The ul_dedined porgon represents the setling of the syslem Control mode
The ucderlff_ed pertloll		represe_Tts the sett ng ot _he system contlel mede

[SL16]	[xsa]	]Receiver			]	[SL16]	[xsa]	[Receiver		!
[SL16]		IDVD	player		SYSTEM	[SL161		DVD	player
[SL16]		]MD	recorder		cord	[SL16]		I MD	recorder	_!	SYSTEM
					CONTROL			,		_	cCO_TROL
[SL16]	[XS] [X$8] [XR]	[Cassette		deck	j]	[ LS_]	[XS, [XSa] ,XR,	_is_		J.]

1..cord.,ayeri][.ecordp,ayer1

•In order to take advantage of the system control operations, the components must be connected to the correct jacks To use a CD player it must be connected to the CD jacks. To use a cassette deck (or M D reco_derI it must be connected to the TAPE 1!MD jacks When using more than one CD player (etc.) only the one connected to the specified iacks may be connected for system control.

•Some CD players and cassette decks are net compatible with the [SL16] system control mode. Be sure to use the [XS8] system control mode

when making system connections with equipment that is not ISL16] compatible.

m Some MD players are not system-control compatible The system control function is nOt aver able when a MD player e used by connecting tt through a d gitaL input You cannot connect the system control cord to this kind of equipment.

1.ISL16} equipment cannot be combined with fXR]. [XS]. and IXS8] equipment for system operations. If your

equipment consists of this kind of combination, p_ease de not connect any system control cords. Even -witheut system control cords, normat operations can be carried out without effecting performance.

2.Do not connect system control cords to any components other than those specified by KENWOOD it may cause a maffunction and damage your equipment.

3= Be sure the system control plugs are inserted all the way in to the system control terminals.

-SYSTEMCONTROLOPERATIONS

Remote Control

Lets you operate this unit with the system remote supplied with the receiver,

Automatic Operation (except [XR] equipment}

When you start playback from a source component, the input

selector on this unit switches to that component automati- cally,

Synchronized Recording (except [XR] equipment)

Lets you synchronize recording with the start of playback when recording from CD, MD or analog discs,

SWITCHING FROM [SL 16] TO[XSS]

You can easty change the system control mode by adjust ng the position of [he SYSTEM CONTROL switch on the rear panel

Do this operation after completing al! connections

For[SL16} SL16 XS8 Forl×Sal

lr

•This operation wilt not effect items stored in the memory

•After switching the system controt mode. turn the power off and then on once to confirm the new sett ng

Registering setup codes for KENWOOD audio components

* Once '_,oufinish makir_g the system connections, be sure to register _.he appropriate setup code for each component.

•If you own remote controllable KENWOOD audio components that are not compatible with system control <or cannot be combined with your

other system contro components), registering the setup code enables you to comtro! those components using the remote contlol supp ied

with this u nit (without con nectrng system control cordsI To reg4ster setup codes for your remote controllable KEI'4WOO D audio components.

see "Setup for controlling AV components"