Kenwood KRF-VBB81 D, VR-2000 instruction manual Laser Disc RF Demodulator DEM-9991D Optional

VR*20_OiVR-208Q/KR_ V88Bl O/KRF V7 7710 {En/K]

Make connections as shown below.

The digital in jacks can accept either DTS, Dolby Digital {AC-3) or PCM (CD Format) signals (the input signal type is detected automatically).

When connecting the related system components, be sure to also refer to the instruction manuals supplied with the components you are connecting.

Do not connect the power cord to a wall outlet until all connections are completed.

The connected components are given as examples because

the available models vary depending on marketing areas.

Connect components capable of output- ting Dolby Digital IAC-3)or standard PCM format digital signals.

LASER DISC RF DEMODULATOR (DEM-9991D)

Note : ©nlyrequi_edifyouwishtoplayLase_Discs

in the Dotby Digital (AC-3) format

To connect an LD player with a Dolby Digital (AC-3)RF OUT or

DIGITAL OUT (Some LD player have a PCM Digital Outputs, in this case

the customer doesn't need the DEM-9991D,)

Connect the LD player to the {optional} KENWOOD LASER DISC RF

DEMODULATOR (DEM-9991D).Then connect the demodulator to the DIGITAL IN (VIDEO4 COAXIAL),

To connect the digital output from an LD player, connect it either to the DIGITAL INPUT OPT, (@_Jor DIGITAL INPUT COAX, ((_;) jack. Connect the vdeo signal and analog audio signals to the V_DEO 4. jacks

(See "Connecting of video components")

ICOAXIAL)	[	[_ r°_.,T-iS_7 i""I!I	DGITALOUT	i
			(OP rlCALI
			AC3 RF OuT

iCOAXIAL)

DIGITAL. OUT_% _C©AX/AL)

Note : Connect either (_ or :_ Should not be corm acted both

To connect an DVD player

with a DIGITAL OUT

_mlm

Q

=

DrGITAL OUT 1_

[OPTICAL)Connect the video signal, S Video signa and analog audio signals to the same serector

(INPUT) jacks,

(See "Connecting of video components" )

Use either the (i_ {COAXIAL) or _ (OPTICAL) jack for the connection of a DVD player,

To the VIDEO 4 COAXIAL jack, connect the input from the DIGITAL OUT (1_ (COAXIAL) jack of a OVD player or the DIGITAL

OUT (# (COAXIAL) Jack of the DEM-gg91D,

LASER DISC RF DEMODULATOR DEM-9991D (Optional)

0 POWER switch

Use to swtch the POWER OFF/POWER ON tOPTJCOAX,),

With the OPT or COAX, position, the input is switched automati- cally to the Dolby Digital (AC-3) RF nput whenever the Dolby Digital (AC-3) RF signal is inpuL

POWER indicator

Lghts (red) when the power switch (O) is set to ON (OPT/COAX t RE LOCK indicator

lights when a Dolby Digital (AC-3) RF sgnal is input to the RF INPUT _AC-3 RF INPUT} iack !_t. tThis ir, dicator is extinguished when a digital input is in use.)

O DIGITAL OUTPUT COAX, (COAXIAL}

Connect this jack to the VIDEO4 COAXIAL (DIGITAL }Nt, jack On you_ Reeiever It outputs Dolby Digital (AC-3) coaxial digital signets when the POWER (O) is set to COAX, and a Dolby Dig tel (AC-3) RF signal is input to the RF tNPbT (AC*3 RE INPUT) iack (_)

Place the power supply away from the demodulator, receiver, and any antennas.

RF INPUT AC-3 RF (Dolby Digital RF)

Connect this jack to the Dolby Dig tat (AC-3) RF OUTPUT jack on your LD 0layer.

DIGITAL INPUT COAX, (COAXIAL)

Connect this jack to the COAXIAL OUTPUT iack on yo_,_ LD player

DIGITAL INPUT OPT, (OPTICAL)

Connect this iack to the OPTICAL OUTPLJT jack on your LD player,

• When there are simuhaneous inputs through the RF iNPUT tAC_3 RE) iack and DIGITAL INPUT jack, the nput through RE INPUT (AC-3 RE) is given the p_iodtv,

ODC tN 12V jack

Connect _hs iack to the AC adaptor suppled witr_ your demodulator

Connect the AC adaptor to a wail outlet after compJeting all of toe other connections.