VR-2OSO/VR2OSO/KRF- -VS881DiKRF+V7771[3[En/K)
When recording sound with a recorder component of KENWOOD, synchro recording is possible by setting the INPUT SELECTOR
to select "Tape1" or "MD" according to the connected component.
Recording a music source
O Select the recording source.
The icons differ according to the setup of +Setup IR" etc.
19 Put the MD recorder or cassette deck to
_+ Select the "MD/Tapel" icon,
Select the MD or cassette deck control icon and put it to
O Play the source and record it.
a When the "Remote | Mode" |
| con is selected, | the | icons of the | |||||||||
components | assigned | to the | inputS, | such | as the "CD1 | ", "Video 1", | ||||||||
"Video2", | "Video3" |
| and | "MD/Tapel" |
| icons | bnk |
| for a | few | ||||
seconds+ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
By select;nO | a | bI+nkng | icon, | the | selected | component | can | be | ||||||
controled | without | switching |
| the | input | selector | (The | "Remote | ||||||
Mode" con | can be used | to put | the | recording | component | to pause | ||||||||
mode w thout | switching |
| the | input | selectory |
|
|
|
|
|
When an icon that is not blinking is selected, the input selector is switched automat sally
•For the recerding procedure of the MD recorder or cassette oeck, refer to its instruction menus
Copying tape (TAPE1 --_ TAPE2)
Caution for recording
The digital signal input through DIGITAL IN is output digitally at the OPTICAL jack+
Make sure the following points to record a digital signal input into the receiver. (The DTS and Dolby Digital
Igl Connect the digital output from the source component to the digital input of the receiver
O Connect the digital output (OPTICAL jack) of the receiver to the digital input (OPTICAL jack} of the MD recorder.
O Record the signal on the recorder component (MD recorderl
|
|
|
|
|
|
| l |
O | Select | the | "MD/Tapel" | input. |
| ||
O | Startplayback | of the cassette deck connected to the | MD/TAPE1 | ] | |||
| input | jacks, | then | start | recording of that connected | to the CD2/ | |
| TAPE2 | MONITOR | input | jacks+ |
|
Digital-* analog recording
By reproducing the digital signal input to the receiver in stereo
(surround mode), the signal can be recorded in analog with the
following procedure,
O | Set | up the | recorder | component | +eady | for | recording |
| |||||||
t_ Select the receiver's input to the source component, | |||||||||||||||
_) | Play the | desired | software. |
|
|
|
|
|
|
| |||||
O | Set | the | "Input |
| Digital" | icon | from | "Auto" | to | "Manual", | |||||
O | In the "Lstn | Mode'* menu | screen, | select | the | "Stereo" icon | |||||||||
O | PFay the | software |
| from | the | beginning | and | record | it. | ||||||
• | Do | not switch | to | "CD2/Tape2 |
| (Monitor)" | during | recording, | |||||||
| This | may | cause | the | interruption | of | the | recording, |
|
Note on CD2/ Tape2 (Monitor)
The following | operations | are | made available | by setting | the | "CD2/Tape2 |
| (Monitor)" | icon | on the | "Setup | Input" | menu | screen to | |||||||
"Tape2 | (Monitor)", | However, | remember | that | these | functions | are available | only | when | the | analog | input/output |
| are | used, | If the | |||||
"CD2/Tape2" | icon | in the | fixed | segments | is selected | during | playback | of a digital | input, | the | input | is switched | to | the analog | input |
and noise may be generated.
ICON
DISPLAY
@
002 ! TAPE2
MONITOR
"Tape2 (Monitor)" setup menu screen
For the setup of the remote control unit, p[ease read "Set "CD2/Tape2"",
Using "CD2/Tape2"
The CD2/TAPE2 | MONITOR | input jacks of the main unit accept e cassette deck or graphic equalizer. | |||||||||||||||||||||
When | a graphic | eelJalizer | is connected, | set "CD2]Tape2" | to | "Tape2" | and | select the | "CD2/Tape2" | ||||||||||||||
icon | in | the | fixed | segments |
| to | on, |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
When | a 3+head | cassette | deck | is connected | to the | CD2iTAPE2 | MONITOR |
| _nput jacks, | the | recorded | ||||||||||||
audio | can | be | monitored |
| during | recording, | and | turning | "CD2/Tape2" |
| on | and | off | allows | you to | ||||||||
compare | the | source audio | and |
| recorded | audio | Refe to the | instructio_ | manuals | of | the | connected | |||||||||||
components |
| for the_ operating procedures, |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
The | "CD2/Tape2 | (Monitor)" | funct+on | is | not | ave | Jab e | during | p ayback | of | a digital | input | Se ecting | ||||||||||
"CD2/Tspe2 |
| (Monitor)" |
| durng | dig tal | input | playback | switches the | input | to | the | analog | input |