23(5$725&219(1,(1&(6

',63/$<

%5,*+71(66

The brightness of the LCD display can be selected from OFF, and 1 to 6 .

1Press [MENU], then press [Q-M.IN]/ [Q-MR]or turn the MULTI/CH control to access Menu No. 00.

2Press [M.IN]/ [SCAN (SG.SEL)] to select “oFF”, “1”, “2”, “3”, “4”, “5”, or “6”.

3Press [MENU] to exit Menu mode.

%$&./,*+7&2/25

You can manually change the display illumination to suit the lighting conditions where you are operating.

1Press [MENU], then press [Q-M.IN]/ [Q-MR]or turn the MULTI/CH control to select Menu No. 01.

2Press [M.IN]/ [SCAN (SG.SEL)] to select “1” (amber) or “2” (green).

3Press [MENU] to exit Menu mode.

3$1(/.(<'28%/()81&7,21 5(63216(7,0(

You can set the response time of double function panel keys to normal or fast. The default setting is normal.

1Press [MENU], then press [Q-M.IN]/ [Q-MR]or turn the MULTI/CH control to select Menu No. 02.

2Press [M.IN]/ [SCAN (SG.SEL)] to select “1” (0.2 second), “2” (0.5 second) or “3” (1 second)

3Press [MENU] to exit Menu mode.

/,1($5$03/,),(5&21752/

When you connect an external HF or 50 MHz linear amplifier to the transceiver using the REMOTE connector, select “1”, “2”, or “3” to activate the internal relay and/ or DC output (12 V) so you can interface with the HF/ 50 MHz linear amplifier. The DC output (12 V) works without any annoying chattering sounds (“1”) but the output current is limited to 10 mA. If your linear amplifier control circuit draws more than DC 12 V/ 10 mA, use relay switching (“2” or “3”) instead.

Also, some linear amplifiers require a long transmission delay time because of the slow antenna relay switching time. In this case, select “3” for slow switching (25 ms delay).

1Press [MENU], then press [Q-M.IN]/ [Q-MR]or turn the MULTI/CH control to select Menu No. 53 (HF) or 54 (50 MHz).

2Press [M.IN]/ [SCAN (SG.SEL)] to select “oFF”, “1”, “2”, or “3”.

3Press [MENU] to exit Menu mode.

Parameter

Linear Amp. Control

oFF

All controls

Disabled

 

 

 

 

DC output (12 V)

Enabled

 

 

 

1

Relay

Disabled

 

 

 

 

TX delay

10 ms

 

 

 

 

DC output (12 V)

Enabled

 

 

 

2

Relay

Enabled

 

 

 

 

TX delay

10 ms

 

 

 

 

DC output (12 V)

Enabled

 

 

 

3

Relay

Enabled

 

 

 

 

TX delay

25 ms

 

 

 

Note: If CW Full Break-in is enabled, 10 ms transmission delay is applied regardless of the settings in Menu Nos. 53 and 54.

/2&.)81&7,216

)5(48(1&</2&.)81&7,21

Frequency Lock disables some keys and controls to prevent you from accidentally activating a function or changing the current settings.

Press and hold [FINE (F.LOCK)] to turn the Frequency Lock function ON or OFF.

•“” appears while this function is ON.

The following keys and controls are disabled by Frequency Lock:

Key

Comments
Tuning control

Still operates in TF-SET mode.

 

 

MULTI/CH

Still operates for changing setting

control

modes.

 

 

[ENT]

 

 

 

[M.IN]

Still operates for character

selection and for changing setting

 

modes.

 

Still operates for character

[SCAN]

selection and for changing setting

modes. Also still operates for

 

setting up scan groups (press

 

and hold).

 

 

 

Still operates in TF-SET mode

Mic [UP]

(in VFO mode) during Menu

mode when the mic key paddle

 

 

operation is ON.

 

 

 

Still operates in TF-SET mode

Mic [DWN]

(in VFO mode) during Menu

mode when the mic key paddle

 

 

operation is ON.

 

 

[A/B]

 

 

 

[M/V]

 

 

 

[SPLIT]

 

 

 

53