23(5$725&219(1,(1&(6

No.

Function

Remark

202

VOICE3

The lower meter when

transmitting

 

 

 

 

 

203

MONITOR

Mic [PF4] default

 

 

 

204

TX TUNE

 

 

 

 

 

 

The input voice from

205

DATA SEND

the data terminal is

 

 

transmitted

206

DOWN

Mic [UP] default

 

 

 

207

UP

Mic [DWN]default

 

 

 

208

EMERGENCY

Emergency frequency

call (K type only)

 

 

OFF

 

No function

 

 

 

Note:

XAssigned key functions may not work, depending on the setting.

X[AGC SEL] can be used in modes other than FM mode, and can set a step level of the chosen AGC time constant (FAST/ SLOW).

X[TONE SEL] can also be used in FM mode while TONE or CTCSS is ON,

'635;(48$/,=(5

(48$/,=,1*5(&(,9,1*$8',2

Use Menu No. 31 to change the receiver frequency responses of the target signal. You can select one from 8 different receiver profiles including the default flat response. Selecting any of the following items

from the Menu causes “” to appear on the display.

•Off (oFF):

Slightly attenuates (1 kHz or higher audio frequencies).

•High boost 1 (hb1):

Emphasizes higher audio frequencies.

•High boost 2 (hb2):

Emphasizes higher audio frequencies but lower audio frequency attenuation is less than High boost1 (hb1).

•Formant pass (FP):

Improves clarity by suppressing audio frequencies outside the normal voice frequency range.

•Bass boost 1 (bb1):

Emphasizes lower audio frequencies.

•Bass boost 2 (bb2):

Emphasizes lower audio frequencies but higher audio frequency attenuation is less than Bass boost1 (bb1).

•Flat (FLAT):

The flat frequency response.

•User (U):

Reserved for the ARCP software. Off is programmed at the factory as a default.

5;021,725

RX monitor temporarily disables the squelch function to monitor the current frequency activities.

To use the RX Monitor function, first assign the function to a PF key (either on the front panel or the microphone).

1Press [MENU], then press [Q-M.IN]/ [Q-MR]or turn the MULTI/CH control to select Menu No. 79 ~ 86.

2Press [M.IN]/ [SCAN (SG.SEL)] to select “203”.

3Press [MENU] to exit Menu mode.

4Press the assigned [PF] key.

• While pressing [PF], the speaker unmutes.

7,0(2877,0(5

The Time-out Timer limits the time of each transmission. It is also useful to prevent a long accidental transmission.

1Press [MENU], then press [Q-M.IN]/ [Q-MR]or turn the MULTI/CH control to access Menu No. 49.

2Press [M.IN]/ [SCAN (SG.SEL)] to select “oFF”, “3”, “5”, “10”, “20”, or “30” minutes.

3Press [MENU] to exit Menu mode.

75$169(57(5

If you have a transverter that converts the TS-590S operating frequencies to other frequencies, you can use this TS-590S transceiver as a transverter exciter. Consult the instruction manual that came with the transverter for interfacing to the TS-590S transceiver.

)5(48(1&<',63/$<

1Connect the transverter to the ANT 1, ANT 2, RX ANT, or DRV connector of the TS-590S.

2Select the exciter operating frequency on the transceiver.

•The transverter will use this frequency as the reference for converting frequencies.

3Press [MENU], then press [Q-M.IN]/ [Q-MR]or turn the MULTI/CH control to access Menu No. 50.

4Press [M.IN]/ [SCAN (SG.SEL)] to select “1”.

•The output power is automatically set to the lowest power for that frequency (default). Refer to “TX POWER” {below}.

5Press [MENU] to exit Menu mode.

6Press [ENT], then set the target converting frequency using the numeric keys.

7Press [ENT] to complete the entry.

•The transceiver displays the target transverter frequency instead of the actual operating frequency.

55