Kenwood TS-2000, TS-2000X, TS-B2000 manual 18

4 GETTING ACQUAINTED

19

20

29

25 27 28 33

CW TUNE

9.6k STA CON

PF
F LOCK	A
ATT	PRE
LEVEL
	LEVEL
VOX
	PROC
SEND	ANT1/2
	AT
PHONES	LEVEL
	N
	.
	R
	.
	LEVEL
	A
	.

CH1/REC	CH2/REC	CH3/REC
1	2
		3
TONE/SEL
	METER
		CTCSS/SEL
4
	5
		6

	MAIN
		AUTO
C	CAR	LSB
	MIC	USB
N
U		REV
F	TX MONI

HF/VHF/UHF ALL MODE MULTI BANDER TS-2000

RIT

						ALT
						XIT
							_
						CLEAR
						P.C.T
						SET
	SUB			NUAL	BC		MAIN
							GAIN
				MA		RF
			QUICK MEMO
MENU	TF-		MR	M.IN
		CALL	C
	SET		IN
			.

RIT/SUB

+

MULTI CH

	N
	.
MIC	MANUAL
	B
	.
	C
	.
	LO/
	WIDTH

NB/LEVEL		AGC/OFF
7		8	FINE/STEP
				9
DCS/SEL
.	SHIFT/OFFSET
		0		ENT
			HI/
		SHIFT

PWR	CW
	FSK
DELAY	NAR
KEY	FM
	AM
CLR		SEL
DISP		1MHz

21 23 24

22

MAIN SUB

SG.SEL

CTRL SCAN

26 32

30 31

	TL
	SA
M/S	REV
A/B	SPLIT
	TRACE
VFO/CH
	A=B
VFO/M
MG.SEL	M.IN
M VFO

MAIN

AF

SQL

SUB

!9LSB/ USB/ AUTO key

Press to select lower sideband (LSB) or upper sideband (USB) mode for voice or digital operation. Press [FUNC], [LSB/ USB/ AUTO] to toggle the auto mode selection {page 73}.

@0CW/ FSK/ REV key

Press to select CW or FSK (Frequency Shift Keying) mode {pages 30, 51}. Press [FUNC],

[CW/ FSK/ REV] to reverse the sideband pitch.

@1FM/ AM/ NAR key

Press to select FM or AM mode {pages 28, 29}. Press [FUNC], [FM/ AM/ NAR] to select narrow bandwidth transmission mode {page 29}.

@2CLR key

Press to exit from, abort, or reset various functions. Also used to erase memory channels {page 62} or locking out memory channels from the scan list {page 62}.

@3DISP key

Press to toggle the normal operating mode and DSP filter setting display mode {page 55}. Press and hold to start the Visual Scan function {page 70}.

@41MHz/ SEL key

Press to switch the MHz Up/ Down function ON or OFF using the MULTI/ CH control. Press [FUNC], [1MHz/ SEL] to change the increment/ decrement step value {page 37}. Press and hold to start the MHz Scan function {page 68}.

@5Tuning control

Turn to select the desired frequency {page 37}. Use the convenient finger-tip cavity for continuous tuning.

The lever behind this control adjusts the control torque level; turn fully clockwise for light torque or fully counterclockwise for heavy torque.

@6CTRL key

Press to toggle the operating controls between the main transceiver and the sub-receiver. The transmission band is not affected by this key.

@7MENU key

Press to select or cancel the Menu mode that is used for activating and configuring functions {page 21}.

@8TF-SET key

While operating split-frequency, press to monitor or change your transmit frequency {page 31}.

@9+/ –(Up/ Down) keys

Press to step through all the Amateur radio bands consecutively {page 18}. Also used to make selections from the Menu {page 21}, and to check the Start and End frequencies of the Scan function {page 62}.

#0MAIN key

Press to transfer the operating controls to the MAIN transceiver. Also moves the transmission band to the main transceiver frequency.

#1SUB key

Press to transfer the operating controls to the sub- receiver. Also moves the transmission band to the sub-receiver frequency.

#2SCAN/ SG.SEL key

Press to start or stop the Scan function {page 66}. Press [FUNC], [SCAN/ SG.SEL] to select a scan group {page 69}.

#3CALL/ C.IN key

Press to recall a call channel for the selected operating band (HF/ 50 MHz/ 144 MHz/ 430 (440) MHz/ 1.2 GHz (TS-2000/ TS-B2000 Optional)). Press [FUNC], [CALL/ C.IN] to write a new Call Channel to the memory {page 75}.

10