8 ENHANCED COMMUNICATIONS
FM DCS OPERATION
Digital Code Squelch (DCS) is another FM application which allows you to ignore (not hear) unwanted calls. It functions the same way as CTCSS. The only differences are the encode/ decode method and the number of selectable codes. For DCS, you can select from 104 different codes listed in the table below.
1Press [A/B] to select VFO A or VFO B.
•“tA” or “tB” appears to show which VFO is selected.
2Select a band.
3Select an operating frequency.
4Press [FM/ AM/ NAR] to select FM mode.
•“FM” appears.
5Turn the SQL control to adjust the squelch.
6Press [•/ DCS/SEL]to switch the DCS function ON (or OFF).
•“DCS” appears when the function is ON.
7Press [FUNC], [•/ DCS/SEL].
•The current DCS code appears. The default is 023.
8Turn the MULTI/ CH control to select the appropriate DCS code.
•The available DCS codes are listed in the following table.
023 | 065 | 132 | 205 | 255 | 331 | 413 | 465 | 612 | 731 |
|
|
|
|
|
|
|
|
|
|
025 | 071 | 134 | 212 | 261 | 332 | 423 | 466 | 624 | 732 |
|
|
|
|
|
|
|
|
|
|
026 | 072 | 143 | 223 | 263 | 343 | 431 | 503 | 627 | 734 |
|
|
|
|
|
|
|
|
|
|
031 | 073 | 145 | 225 | 265 | 346 | 432 | 506 | 631 | 743 |
|
|
|
|
|
|
|
|
|
|
032 | 074 | 152 | 226 | 266 | 351 | 445 | 516 | 632 | 754 |
|
|
|
|
|
|
|
|
|
|
036 | 114 | 155 | 243 | 271 | 356 | 446 | 523 | 654 |
|
|
|
|
|
|
|
|
|
|
|
043 | 115 | 156 | 244 | 274 | 364 | 452 | 526 | 662 |
|
|
|
|
|
|
|
|
|
|
|
047 | 116 | 162 | 245 | 306 | 365 | 454 | 532 | 664 |
|
|
|
|
|
|
|
|
|
|
|
051 | 122 | 165 | 246 | 311 | 371 | 455 | 546 | 703 |
|
053 | 125 | 172 | 251 | 315 | 411 | 462 | 565 | 712 |
|
|
|
|
|
|
|
|
|
|
|
054 | 131 | 174 | 252 | 325 | 412 | 464 | 606 | 723 |
|
|
|
|
|
|
|
|
|
|
|
9Press [FUNC], [•/ DCS/SEL]again to complete the setting.
You will hear calls only when the selected code is received. To answer the call, press [SEND] or press and hold Mic [PTT], then speak into the microphone.
Skip steps 7 to 9 if you have already programmed the appropriate DCS code.
Note: You cannot use DCS with the Tone or CTCSS functions.
DCS CODE ID SCAN
This function scans through all DCS codes to identify the incoming DCS code on a received signal. You may find this useful when you cannot recall the DCS code that the other persons in your group are using.
1Press [FUNC], [•/ DCS/SEL].
•The current DCS code appears.
2Press [SCAN/ SG.SEL] to activate the DCS Code ID scan.
•“DCS” blinks and every DCS code is scanned. When the DCS code is identified, the transceiver stops scanning and the identified DCS ID is displayed.
•Press [SCAN/ SG.SEL] to resume scanning.
•Press [SCAN/ SG.SEL] to stop scanning while the DCS code ID scan is active.
Note: Received signals are audible while scanning is in progress.
36