15 OPERATOR CONVENIENCES

USING TH-D7A AS A COMMANDER

To use a TH-D7A transceiver as a “Commander” (an external remote control unit), follow the steps below. Basically, it is the same as using a TM-D700A as a “Commander” (described on the previous page).

TS-2000(X) (Transporter) Setup:

1Press [MENU], then turn the MULTI/ CH control to access Menu No. 62A.

2Enter your callsign (ex: WD6DJY) as a “Commander” callsign, using [+]/ [–]or the MULTI/ CH control. To move the cursor, press [MAIN] or [SUB]. Press [M.IN] to store the callsign to Menu No. 62A.

3Press [MENU], then turn the MULTI/ CH control to access Menu No. 62B.

4Enter your alias callsign (ex: WD6DJY-1) as a “Transporter” callsign, using [+]/ [–]or the MULTI/ CH control. To move the cursor, press [MAIN] or [SUB]. Press [M.IN] to store the callsign to Menu No. 62B.

Note: You can use alpha-numeric characters, A to Z, 0 to 9 and “-”. The callsign must be no more than 9 characters long including “-”. Also, the following callsign formats cannot be entered:

•WD6DJYZ

If you use only letters and numbers for the callsign, the maximum length is 6 characters.

•WD6-DJY-1

You cannot use more than 1 “-” within a callsign.

•-WD6DJY

You cannot use a “-” as the first callsign character.

•WD6DJY-19

An SSID must be within the range of 1 to 15.

5 Access Menu No. 62C, then turn the MULTI/ CH

control to select a CTCSS tone frequency for Sky

Commander II+ (default is 88.5 Hz).

4Set the same frequencies that you selected for the “Transporter” for the VHF and UHF bands.

Note: Refer to Chapter 19, Sky Command II, of the TH-D7A instruction manual for details on how to enter the callsign and CTCSS tone frequency.

CONTROL OPERATION

First, switch the TS-2000 transceiver ON and select T-PORTER (Transporter) from Menu 62E.

Then, access Menu 4–4 on the TH-D7A and select “COMMANDER”. “PUSH [0] KEY TO START COMMANDER!!” appears.

Press [0] on the TH-D7A to start Sky Command mode.

When in Sky Command mode, the keys of the TH-D7A (Commander) will function as described below. Only [LAMP], [MONI], and the VOL control functions will not change.

Each time you press the desired key, the Commander will automatically enter transmit mode and send the corresponding control command to the TS-2000 (Transporter).

To switch the HF

6 Access Menu No. 62D and select the

transceiver OFF

Press [POWER].

communication speed for Sky Command II+.

To transmit audio on a

Press and hold the PTT

Select 1200 bps for TH-D7A (9600 bps can be

used only when you use another TS-2000 as a

HF frequency

switch, then speak into the microphone.

“Commander”).

To receive audio on an

7 Assign the TNC band to the sub-band by

HF frequency

Press [RX].

accessing Menu No. 46 and select SUB.

8 Select a 144 MHz band frequency in FM mode on

the main transceiver and 440 MHz band frequency

in FM mode for the sub-receiver for Sky Command

operation.

TH-D7A (Commander) Setup:

1Access Menu 4–1 to enter the same callsign that you entered for the Commander (ex: WD6DJY).

2Access Menu 4–2 to enter the same callsign that you entered for the Transporter (ex: WD6DJY-1).

3Access Menu 4–3 to select the same CTCSS tone frequency that you selected for the TS-2000(X) (Transporter).

To monitor the UHF band Press and hold [MONI]. on the Commander

85