Preparing for surround sound

If you have selected “NML” as the Front speakers setting,

1

CNTR NML (normal) : An average size Center speaker is

 

 

connected to this model.

2

CNTR OFF

: Center speaker setting mode to this

 

 

model is OFF.

9Press the SETUP key again to accept the setting.

•The surround speaker setting indication “SURR NML” appears.

0Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the appropriate Surround speaker setting.

If you have selected “LRG” as the Center speaker setting,

1SURR NML (normal) : Average size Surround speakers are connected to this model.

2SURR LRG (large) : Large Surround speakers are connected to this model.

3 SURR OFF

: Surround speaker setting mode to this

 

model is OFF.

If you have selected other than “LRG” as the Center speaker

setting,

 

1

SURR NML (normal): Average size Surround speakers are

 

 

connected to this model.

2

SURR OFF

: Surround speaker setting mode to this

 

 

model is OFF.

•When the setting “SURR OFF” is selected, the procedure skips to step #.

!Press the SETUP key to accept the setting.

•The Surround Back speaker setting indication “BS” appears.

@Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the appropriate Surround Back speaker setting.

If you have selected “LRG” as the surround speaker setting, 1 BS NML (normal : Average size Surround back speakers are

connected to this model.

2BS LRG (large) : Large Surround Back speaker is connected to this model.

3 BS OFF

: Surround Back speaker setting mode to

 

this model is OFF.

If you have selected “NML” as the Surround speaker setting,

1

BS NML (normal) : Average size Surround Back speakers are

 

 

connected to this model.

2

BS OFF

: Surround Back speaker setting mode to

 

 

this model is OFF.

(VR-60RS only)

If you have selected “LRG” or “NML” as the surround back speaker setting.

1 SPEAKER : Surround Back signal will be output from SURROUND BACK speaker terminal, and SURR BACK L/ SURR BACK PRE OUT terminal as monaural.

2 PRE OUT : Surround Back signals will be output from SURR BACK L/ SURR BACK and SURR BACK R PREOUT terminals as stereo.

#Press the SETUP key again to accept the setting.

•The subwoofer re-mix setting indication “SW RE-MIX” scrolls across the display.

•If subwoofer is turned OFF, subwoofer re-mix setting is not visible.

$Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the appropriate Subwoofer re-mix setting.

1 RMX ON : Subwoofer re-mix set mode to this model is ON.

2 RMX OFF : Subwoofer re-mix set mode to this model is OFF.

%Press the SETUP key to accept the setting.

4Adjust the speaker volume level.

From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same.

•In step 4 and 5, indications appear only for the selected channels of the speakers that require adjusting.

1 Press the SETUP key to begin TEST TONE.

•This model enters the speaker volume level adjustment mode.

The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or MULTI CONTROL %/fi keys.

1

AUTO

2

MANUAL

2Press the SETUP key again to select either AUTO or MANUAL.

Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to adjust the volume level of the test tone output from the speaker channel to be adjusted.

For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each:

• If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also

changed.

•If any of the speaker is set as OFF during SP SET UP, the TEST TONE adjustment for the speaker will be skipped.

(VR-60RS only)

•If you have selected “SPEAKER” as the Surround Back setting, “RB” and “LB” are not appeared but “BS” is appeared.

3Press the SETUP key.

•The test tone is turned off. This model enters the mode for inputting the distance to the speakers.

4For MANUAL selection, press the SETUP key each time to select the speaker channel.

5Input the distance to the speakers.

1Select the DISTANCE from the set up displays and press the SETUP key again.

2Measure the distance from the listening position to each of the speakers.

Jot down the distance to each of the speakers.

Distance to Front Left speaker (L)

: ____ feet (meters)

Distance to Center speaker (C)

: ____ feet (meters)

Distance to Front Right speaker (R)

: ____ feet (meters)

Distance to Surround Right (RS)

: ____ feet (meters)

Distance to Surround Back Right (RB) : ____ feet (meters)

Distance to Surround Back (BS)

: ____ feet (meters)

Distance to Surround Back Left (LB)

: ____ feet (meters)

Distance to Surround Left (LS)

: ____ feet (meters)

Distance to Subwoofer (SW)

: ____ feet (meters)

(VR-60RS only)

•If you have selected “SPEAKER” as the Surround Back setting, “RB” and “LB” are not appeared but “BS” is appeared.

Continued to next page

17 EN