Table of Contents

Section 1: Assembly and Set-Up

Land Pride

Pull-Type Tractor Hook-Up

Refer to Figure 1-17

!DANGER!

Crushing Hazard between tractor and implement. Do not allow anyone to stand between the tractor and implement while backing-up to an implement. Never operate the hydraulic

3-point lift controls while someone is directly behind the tractor.

Refer to Figure 1-17:

IMPORTANT: Jack attachment pin (#2) must be fully inserted and secured before working on or around a cutter that is not hooked to the tractor drawbar.

1.Make certain jack stand (#1) is properly attached to the cutter hitch and secured with attachment pin (#2).

2.Back tractor within close proximity of cutter clevis (#6).

3.Raise or lower jack (#1) to align clevis (#6) with tractor drawbar. Drawbar should fit between lower and upper plates of clevis.

4.Back tractor up to cutter hitch until holes in the drawbar and clevis (#6) are aligned.

5.Insert 1" flat washers (#5) above and below tractor drawbar.

6.Insert 1” -8 x 4 1/2” gr5 hex bolt (3) through top of clevis (#6), 1" washer (#5), drawbar, remaining 1" washers (#5) and out through bottom of clevis (#6). Secure hex bolt with locknut (#4). Tighten nut snugly to remove all play and then back nut one-quarter turn.

NOTE: May need to adjust the leveling rod nut couplers to obtain correct drawbar height.

7.Attach driveline yoke end (#8) to tractor PTO shaft. Secure with locking device. Pull on both end of the driveline to make sure it is secured to the tractor and gearbox shafts.

8.Attach hydraulic hose (#9) to tractor hydraulic outlet.

9.Fully retract the jack stand (#1), remove locking pin (#2) and store parking jack on the cutter deck with locking pin as shown.

Safety Chains

Refer to Figure 1-17:

When towing implements on the highway, use a safety chain (#7) with tensile strength equal to or greater than the gross weight of the implement to be towed by the tractor. This will control the implement in the event the hitch pin is lost.

Attaching safety chain (#7) to the tractor. Lock chain hook securely to the safety chain. Make a trial run by driving the tractor to the right and to the left for a short distance to check the safety chain adjustment. If necessary, re-adjust to eliminate a tight or loose chain.

Pull-Type Tractor Un-Hook

Refer to Figure 1-17

1.Park cutter on a level solid hard surface. Place tractor gear selector in park and set park brake.

NOTE: Always place jack stand on firm surface or place board under jack stand for support.

RCR2510 is shown. Jack is located on the deck in the transport position on the RCR2596.

Pull-Type Tractor Hook-Up

Figure 1-17

20 RCR2596, RCR2510 and RCRM2510 Rotary Cutters 312-753M

5/09/08

Page 21 Page 23
Page 22
Image 22
Land Pride RCRM2510, 312-753M, RCR2596, RCR2510 manual Pull-Type Tractor Hook-Up, Pull-Type Tractor Un-Hook, Safety Chains
Page 21 Page 23

312-753M, RCR2510, RCRM2510, RCR2596 specifications

Land Pride, a leading manufacturer of agricultural and landscaping equipment, has established a strong reputation for producing innovative and durable products. Among their diverse range of offerings are the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 models, each engineered with specific features to cater to various land management and maintenance tasks.

The Land Pride 312-753M is an advanced grooming mower designed for meticulous finishing work in landscape applications. With a cutting width of 75 inches, it is suitable for a range of tasks from mowing parks to maintaining golf course fairways. Its floating deck design allows for optimal contour following, ensuring a clean cut even on uneven terrain. The mower features a robust construction with reinforced edges that enhance durability, and the blade tip speed maximizes cutting efficiency.

Next in the lineup, the RCR2596 rotary cutter is engineered for heavy-duty mowing, making it ideal for clearing tall grass and brush in fields and pastures. With a 96-inch cut width, the RCR2596 boasts a rugged design that can handle various terrains and dense vegetation. Its heavy-duty gearboxes and cutting blades are built to last, providing operators with peace of mind during extensive operations. The RCR2596 also includes a side skirt that improves safety by containing debris while mowing.

The RCRM2510 is a robust rotary cutter that combines performance with efficiency. Designed for smaller tractors, it features a 10-foot cutting width, making it an excellent choice for tasks demanding precision and power. The RCRM2510 incorporates a fully adjustable hitch that allows for easy attachment to various tractor models. Additionally, its floating design permits it to follow the contours of the land, optimizing its cutting capabilities across diverse landscapes.

Lastly, the RCR2510 model is another addition to the rotary cutter series, renowned for its versatile applications. With a cutting width of 10 feet, it is perfect for managing overgrown fields, pastures, and large landscaped areas. The RCR2510 features heavy-duty construction intended to withstand challenging conditions, ensuring longevity and reliability. Its user-friendly design facilitates easy maintenance, and the premium blades deliver exceptional cutting performance.

In summary, the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 rotary cutters offer exceptional capabilities tailored to meet the needs of both professional landscapers and agricultural operators. Their advanced features, reliable construction, and innovative technologies set a high standard in the industry, making them essential tools for effective land management.
Top Page Image Contents