Manuals / Land Pride / Lawn and Garden / Brush Cutter

Land Pride RCR2510 manual Cutting Instructions, Turning Angles for Pull-Type Cutters, CV Driveline

Models: 312-753M RCR2510 RCRM2510 RCR2596

1 42
Download 42 pages 57.58 Kb
Page 27
Image 27

Land Pride

Table of Contents

Section 3: Operating Procedures

Cutting Instructions

!DANGER!

The use of front & rear safety shields is strongly recommended to prevent injury or death caused by thrown objects! Gearbox shields must be secured in place when operating to avoid injury or death from entanglement in rotating drivelines.

!DANGER!

Rotary Cutters have the ability to discharge objects at high speeds. Therefore, the use of front & rear safety guards is strongly recommended to prevent injury or death caused by thrown objects!

This cutter was designed to cut grass and medium brush in right-of-ways, pastures and for shredding row crop residues.

1.Thoroughly Inspect the area to be cut for debris and unforeseen objects. Mark any potential hazards.

2.Start machine slowly allowing cutter blades to become aligned properly before going to full power.

3.It is important to maintain correct RPM PTO speed. Loss of PTO speed will allow blades to hinge back and result in ragged, uneven cutting.

4.Never run fast enough to overload the tractor or cutter. Ground speed depends on two things:

•The density of material being cut.

•Size of tractor operating the cutter.

!CAUTION!

Damage may occur if exceeding the rated cutting capacity of the cutter!

!CAUTION!

Do not over speed PTO or machine damage may result. The 8’ model in this series is available in 540 RPM. The 10’ model in this series is available in 540 RPM or 1000 RPM. Know what your tractor requirements are.

!WARNING!

The RCR25 series cutter is designed to cut grass and brush up to 1” in diameter. Using his cutter for any other type of work can damage the drive components, deck and support frame.

!DANGER!

Do not use deck as a fan. Cutting blades are not properly designed or guarded for this use. Using the deck as a fan can result in injury and/or death.

!DANGER!

Do not operate and/or travel across steep inclines where a tractor can roll-over resulting in serious injury or death. Consult your tractor’s manual for acceptable inclines the tractor is capable of traveling across.

!CAUTION!

Tractor PTO shield and all Rotary Cutter guards must be in place at all times during operation!

IMPORTANT: Avoid catching the hydraulic hoses on brush, post, stumps, and other protrusions that could damage and/or break them.

NOTE: Your cutter is equipped with free swinging cutting blades to reduce shock loads to the cutter if striking obstacles.

5.After the first 50 feet, stop and check to see that the cutter is adjusted properly.

6.Do not engage PTO with 3-point in the fully raised or position.

7.Periodically disengage PTO, turn off tractor, remove ignition key and check for foreign objects wrapped around the rotor shaft. Block cutter deck up before removing objects.

Turning Angles for Pull-Type Cutters

Refer to Figure 3-1 and 2-3:

Avoid tractor-to-cutter turning angles exceeding 35 degrees if the main driveline is a standard conventional drive shaft. The turning angle may be increased to 80 degrees if equipped with a constant velocity driveline shaft. These extreme angles are intended for intermittent usage only and not prolonged usage. Plan your field cutting to minimize the number of turns as well as extreme angles where turns are necessary.

11934

Conventional U-Joint Driveline

Figure 3-1

20795

CV Driveline

Figure 3-2

5/09/08

RCR2596, RCR2510 and RCRM2510 Rotary Cutters 312-753M

25

Page 26 Page 28
Page 27
Image 27
Land Pride RCR2510, 312-753M Cutting Instructions, Turning Angles for Pull-Type Cutters, Conventional U-Joint Driveline
Page 26 Page 28

312-753M, RCR2510, RCRM2510, RCR2596 specifications

Land Pride, a leading manufacturer of agricultural and landscaping equipment, has established a strong reputation for producing innovative and durable products. Among their diverse range of offerings are the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 models, each engineered with specific features to cater to various land management and maintenance tasks.

The Land Pride 312-753M is an advanced grooming mower designed for meticulous finishing work in landscape applications. With a cutting width of 75 inches, it is suitable for a range of tasks from mowing parks to maintaining golf course fairways. Its floating deck design allows for optimal contour following, ensuring a clean cut even on uneven terrain. The mower features a robust construction with reinforced edges that enhance durability, and the blade tip speed maximizes cutting efficiency.

Next in the lineup, the RCR2596 rotary cutter is engineered for heavy-duty mowing, making it ideal for clearing tall grass and brush in fields and pastures. With a 96-inch cut width, the RCR2596 boasts a rugged design that can handle various terrains and dense vegetation. Its heavy-duty gearboxes and cutting blades are built to last, providing operators with peace of mind during extensive operations. The RCR2596 also includes a side skirt that improves safety by containing debris while mowing.

The RCRM2510 is a robust rotary cutter that combines performance with efficiency. Designed for smaller tractors, it features a 10-foot cutting width, making it an excellent choice for tasks demanding precision and power. The RCRM2510 incorporates a fully adjustable hitch that allows for easy attachment to various tractor models. Additionally, its floating design permits it to follow the contours of the land, optimizing its cutting capabilities across diverse landscapes.

Lastly, the RCR2510 model is another addition to the rotary cutter series, renowned for its versatile applications. With a cutting width of 10 feet, it is perfect for managing overgrown fields, pastures, and large landscaped areas. The RCR2510 features heavy-duty construction intended to withstand challenging conditions, ensuring longevity and reliability. Its user-friendly design facilitates easy maintenance, and the premium blades deliver exceptional cutting performance.

In summary, the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 rotary cutters offer exceptional capabilities tailored to meet the needs of both professional landscapers and agricultural operators. Their advanced features, reliable construction, and innovative technologies set a high standard in the industry, making them essential tools for effective land management.