Table of Contents

Section 1: Assembly and Set-Up

Land Pride

!WARNING!

Damaged drivelines can cause serious injury or death.

aligned and level with the tractor's PTO shaft. Securely block cutter deck in this position.

2.Place tractor gear selector in park, shut tractor engine off, set park brake and remove switch key.

Either a tractor with 540 rpm or 1000 rpm PTO (Power Take-Off) speed is required. The RCR cutters are designed for a PTO speed of 540 rpm and the RCRM cutters are designed for 1000 rpm.

IMPORTANT: Do not attempt to operate a 540 RPM driveline cutter with a 1,000 RPM PTO tractor and do not operate a 1000 RPM driveline cutter with a 540 RPM PTO tractor. Many tractors provide both 540 and 1,000 RPM PTO speeds. Check your tractor’s manual to determine its capabilities.

3.Attach driveline to cutter and tractor as follows:

a.Slide inner yoke of driveline over the gearbox shaft and secure with locking collar.

b.Slide outer yoke of driveline over the tractor's PTO shaft and secure with locking collar.

c.Skip to step 5 if driveline fits between tractor and Rotary Cutter.

Refer to Figure 1-16:

4.The driveline will require shortening if it is too long to fit between the tractor and Rotary Cutter. Shorten driveline as follows:

IMPORTANT: Avoid premature driveline breakdown. A driveline that is operating must not exceed an angle of 25 degrees up or down while operating 3-point lift. See Figure 1-15 below.

24872

Maximum PTO Driveline Movement During Operation

Figure 1-15

Checking Driveline Minimum Length

a.Check to make sure cutter and tractor PTO shafts are level with each other and the deck is securely supported at this height with support blocks.

b.Pull driveline profiles apart into two sections as shown in Figure 1-16.

22311

Driveline Shortening

Figure 1-16

IMPORTANT: Always check driveline minimum length during initial setup, when connecting to a different tractor and when alternating between using a quick hitch and a standard 3-point hitch. More than one driveline may be required to fit all applications.

IMPORTANT: It is necessary to align and level the tractor’s PTO shaft with the gearbox shaft when checking driveline minimum length. Too long a driveline can damage tractor, gearbox and driveline.

Refer to Figure 1-14 on page 17:

1.Obtain the shortest distance possible between tractor PTO shaft and gearbox shaft by starting the tractor and slowly engaging 3-point lift to move the lower arms up or down until the gearbox shaft is

c.Attach outer driveline universal joint to tractor PTO shaft and inner driveline universal joint to gearbox shaft. Pull on each driveline section to be sure universal joints are secured.

d.Hold driveline sections parallel to each other to determine if they are too long. The inner and outer shields on each section should end approximately 1" short of reaching the universal joint shield on the adjacent section (see “B” dimension). If they are too long, measure 1" (“B” dimension) back from the universal joint shield and make a mark at this location on the inner and outer shields.

e.Cut off inner shield at mark (“X” dimension). Cut same amount off inner shaft (“X1” dimension). Repeat cut off procedure (“Y” & “Y1” dimensions) to cut outer driveline half.

f.Remove all burrs and cuttings.

18 RCR2596, RCR2510 and RCRM2510 Rotary Cutters 312-753M

5/09/08

Page 19 Page 21
Page 20
Image 20
Land Pride 312-753M, RCR2596, RCRM2510 Checking Driveline Minimum Length, Maximum PTO Driveline Movement During Operation
Page 19 Page 21

312-753M, RCR2510, RCRM2510, RCR2596 specifications

Land Pride, a leading manufacturer of agricultural and landscaping equipment, has established a strong reputation for producing innovative and durable products. Among their diverse range of offerings are the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 models, each engineered with specific features to cater to various land management and maintenance tasks.

The Land Pride 312-753M is an advanced grooming mower designed for meticulous finishing work in landscape applications. With a cutting width of 75 inches, it is suitable for a range of tasks from mowing parks to maintaining golf course fairways. Its floating deck design allows for optimal contour following, ensuring a clean cut even on uneven terrain. The mower features a robust construction with reinforced edges that enhance durability, and the blade tip speed maximizes cutting efficiency.

Next in the lineup, the RCR2596 rotary cutter is engineered for heavy-duty mowing, making it ideal for clearing tall grass and brush in fields and pastures. With a 96-inch cut width, the RCR2596 boasts a rugged design that can handle various terrains and dense vegetation. Its heavy-duty gearboxes and cutting blades are built to last, providing operators with peace of mind during extensive operations. The RCR2596 also includes a side skirt that improves safety by containing debris while mowing.

The RCRM2510 is a robust rotary cutter that combines performance with efficiency. Designed for smaller tractors, it features a 10-foot cutting width, making it an excellent choice for tasks demanding precision and power. The RCRM2510 incorporates a fully adjustable hitch that allows for easy attachment to various tractor models. Additionally, its floating design permits it to follow the contours of the land, optimizing its cutting capabilities across diverse landscapes.

Lastly, the RCR2510 model is another addition to the rotary cutter series, renowned for its versatile applications. With a cutting width of 10 feet, it is perfect for managing overgrown fields, pastures, and large landscaped areas. The RCR2510 features heavy-duty construction intended to withstand challenging conditions, ensuring longevity and reliability. Its user-friendly design facilitates easy maintenance, and the premium blades deliver exceptional cutting performance.

In summary, the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 rotary cutters offer exceptional capabilities tailored to meet the needs of both professional landscapers and agricultural operators. Their advanced features, reliable construction, and innovative technologies set a high standard in the industry, making them essential tools for effective land management.
Top Page Image Contents