Table of Contents

Section 4: Maintenance & Lubrication

Land Pride

Drive Belt Replacement Instructions

Refer to Figure 4-11on page 33:

1.Park unit on a flat surface. Stop engine and remove ignition key. Make sure blade engagement switch is in the down (OFF) position. Spread control levers fully apart and set park to (ON).

8.Slide the belt over the IZT pulleys (#6).

9.Slide the belt off of the fixed idler pulley (#8).

10.The belt can now be removed from above the engine pulley (#2).

!WARNING

Make sure engine and engine muffler is completely cooled before working on and around the drive belt. Server burns to the body could result if engine and muffler have not cooled.

2.Disconnect negative battery cable.

3.Place deck height in the lowest position.

4.Remove deck drive belt (#1 in Figure 4-10)from the electric clutch pulley (#3) as outlined in “Deck Belt Replacement Instructions” on Page 33. This belt does not need to be removed from any of the other deck pulleys.

5.Release belt tension from the IZT units (#6) by pulling on the idler pulley (#4) (extending spring (#7) carefully) and sliding the belt over the pulley. Use caution when releasing the idler pulley as there is still tension on it and it will snap back into position.

6.Remove clutch restraint bracket (#9) by removing the two 1/4"-20 GR5 hex flange head screws and hex flange nuts (#10)

7.Slide the belt off and above the engine pulley (#2). The belt will have to be slid above the engine pulley to allow the belt to be removed from the other pulleys. Refer to Figure 4-12.

Drive Belt on

Engine Pulley

Deck Belt on

Clutch Pulley

23632

Pump/Motor Belt Removal

Figure 4-12

11.Install new belt by sliding it up and over the engine pulley (#2). Make certain it is not in the pulley groove at this time but is above the pulley.

12.Slide the belt over the fixed idler pulley (#8) and then over the IZT pulleys (#6).

13.Slide the belt onto the engine pulley (#2).

14.Pull the idler pulley (#4) over and slide the belt onto it.

Make certain to keep fingers from getting between the belt and the pulley when the pulley is released and tension is re-established.

15.Re-install the deck drive belt on the electric clutch pulley and make sure it is routed properly on all of the deck pulleys.

16.Reattach clutch restraint bracket (#9) with two 1/4"-20 GR5 hex flange head screws and hex flange nuts (#10). Tighten nuts to correct torque.

17.Re-tension the deck belt idler per the “Deck Belt Replacement Instructions” on page 33.

18.Re-attach the negative battery cable.

Mower Blade Maintenance

Blade Inspection

Check the mower blades daily, they are the key to power efficiency and well groomed turf. Keep them sharp, a dull blade will tear rather than cut the grass, leaving a brown ragged top on the grass within a few hours. A dull blade also requires more power from the engine.

Replace any blade which is bent, cracked or broken.

!WARNING

DO NOT try to straighten a blade that is bent. Never weld a broken or cracked blade. ALWAYS replace with a new Land Pride blade to assure safety.

!DANGER

Never work with blades while engine is running or blade is engaged. Always place blade engagement switch in the down (Off) position, place both control levers in neutral position, place park lever in (ON) position and turn engine off. Block up mower when you must work under it. Wear gloves when handling blades. Always check for blade damage if mower strikes rock, branch or other foreign object during mowing!

34 Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

2/27/07

Page 36
Image 36
Land Pride 357-044M manual Mower Blade Maintenance, Drive Belt Replacement Instructions, Blade Inspection, Refer to -11on

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.