LENNOX HEARTH PRODUCTS • MONTEBELLO®
MAINTENANCE
(See Maintenance Schedule, Page 22)
Refer to the maintenance schedule for maintenance tasks, procedures, frequency and by whom they should be performed. Always verify proper operation of the appliance after servicing.
WARNING
Turn off gas and electrical power to the fireplace and allow it to cool before cleaning or servicing the appliance.
CAUTION: Wear gloves and safety glasses for protection while doing required maintenance.
Verify proper operation after servicing.
S’assurer que l’appareil fonctionne
Always turn OFF gas to the pilot before cleaning. Before relighting, refer to the lighting instructions in this manual. Instructions are also found on a
Inspect Venting System
The appliance and venting system should be thoroughly inspected before initial use and at least annually by a qualified service techni- cian (inspection should include ensuring that exhaust or intake passages are unobstructed and vent components are properly assembled and not damaged). Homeowner must contact a qualified service technician at once if any abnormal condition is observed.
If the venting system is disassembled for any reason, a qualified service technician should follow vent installation instructions for proper reassembly and proper sealing of the venting system components. However, more frequent periodic inspections and cleanings should be performed by the homeowner.
Glass Cleaning
(For detailed glass door assembly removal/ installation instructions, see Page 12 .)
Note: Clean glass after first two weeks of operation (after
IMPORTANT: Do not use abrasive cleaners on glass. Never clean the glass when it is hot.
Clean the glass periodically, to remove any buildup caused by the following:
•Filmy coating (during initial use after instal- lation). Initial curing of the high temperature paint and burning off of lubricants used in the manufacturing process may result in a filmy coating on the glass.
•Dusty or dirty buildup. It is normal for con- densation and fog to form on the inside of the glass when first starting the appliance. This condensation and fog will usually disappear within a few minutes; however, over time the moisture can cause lint, dust, and other airborne particles to cling to the glass surface.
•White coating. A white coating may form on the glass as a result of impurities and minerals in the fuel.
It is recommended that the glass be cleaned two or three times during each heating season, depending on the circumstances. The follow- ing cleaning solutions are approved for use to clean the glass:
•
•50% white vinegar and 50% water
•Gas fireplace/stove glass cleaner
Inspect Glass Gasket
Visually inspect the gasket on the backside of the glass enclosure panels. The gasket surface must be clean, free of irregularities and seated firmly.
Clean Control Compartment
Keep control compartment clean by vacuuming or brushing at least twice a year. More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is important that control compartments, burners and circulating air passageways of the appliance be kept clean.
Clean Logs and Burner
Carefully remove the logs (use care when han- dling the fiber logs, as they become quite fragile after curing). Vacuum out any foreign matter (lint, carbon, etc.) on the burner. Ensure the burner ports are “open.” Remove any carbon deposits from the under side of the logs using a vacuum cleaner, or a soft bristled brush (i.e. paint brush).
Note: Improper positioning of logs can create carbon
Replacing Logs
If the logs become damaged by accident or improper handling and need replacement, use only the proper replacement logs from manufacturer (see Pages 17, 25, and 26 for ordering information).
Reinstall Embers, Volcanic Stone, and Logs
Carefully follow placement instructions on Pages
Inspect Wiring
Refer to wiring diagram on Page 17.
CAUTION: Label all wires prior to disconnec- tion when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
ATTENTION: Au moment de l’entretien des commandes, étiquetez tous les fils avant de les débrancher. Des erreurs de cáblage peuvent entraîner un fonctionnement inadéquat et dangereux.
Inspect and clean all wire connections. Ensure that there is no melting or damage. Inspection should include terminals at the valve.
Inspect Burner Flame Appearance
Ensure that the burner flame appearance resembles the flame shown in Figures 21 and
22and as described in “Flame Appearance and Sooting” on Page 16. The homeowner must contact a qualified service technician at once if any abnormal condition is observed.
Small Area Paint Touch-up
Only use a factory supplied paint kit for touch- ups. Paint is available at your local authorized Lennox Hearth Products dealer. Never attempt to paint a hot fireplace.
If the surface later becomes stained or marred, it may be lightly sanded and touched up with spray paint.
11
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
