Low speaker volume, Set Pulse dial as default, Sr? | Lenovo 9212

Command		Function

	H1	Force modem off-hook (make busy)
		Note: H1 command is not supported for Italy

I_	I0	Display product-identification code

	I1	Factory ROM checksum test

	I2	Internal memory test

	I3	Firmware ID

	I4	Reserved ID

L_	L0	Low speaker volume

	L1	Low speaker volume

	L2	Medium speaker volume

	L3	High speaker volume

M_	M0	Internal speaker off

	M1	Internal speaker on until carrier detected

	M2	Internal speaker always on

	M3	Internal speaker on until carrier detected and
		off while dialing

N_		Included for compatibility only, provides no
		effect

O_	O0	Return to Data Mode

	O1	Return to Data Mode and initiate an equalizer
		retrain

P		Set Pulse dial as default

Q_	Q0	Modem sends responses

Sr?		Read and display value in register r.

Sr=n		Set register r to value n (n = 0-255).

T		Set Tone Dial as default

V_	V0	Numeric responses

	V1	Word responses

W_	W0	Report DTE speed only

	W1	Report line speed, error correction protocol,
		and DTE speed.

	W2	Report DCE speed only

X_	X0	Hayes Smartmodem 300 compatible
		responses/blind dialing.

	X1	Same as X0 plus all CONNECT
		responses/blind dialing

	X2	Same as X1 plus dial tone detection

	X3	Same as X1 plus busy detection/blind dialing

	X4	All responses and dial tone and busy signal
		detection

Z_	Z0	Reset and retrieve active profile 0

	Z1	Reset and retrieve active profile 1

34User Guide

Image 50

Lenovo 9212, 9213 Low speaker volume, Internal speaker on until carrier detected, Set Pulse dial as default, Sr?, Sr=n

Contents

User Guide Types 9212 Page User Guide Types 9212 Page Contents Iv User Guide Important safety information Conditions that require immediate action General safety guidelines Service Power cords and power adapters Extension cords and related devices Plugs and outlets Batteries CD and DVD drive safety Heat and product ventilation To connect To disconnect Additional safety informationLithium battery notice Modem safety information Laser compliance statement Power supply statement Overview Information resources Xiv User Guide Installing options Features Memory Operating systems, preinstalled varies by model type Available options Specifications Tools required Installing external options Handling static-sensitive devices Locating the connectors on the front of your computer Locating the connectors on the rear of your computer Connector Description Obtaining device drivers Removing the cover Locating components Identifying parts on the system board Installing memory modules Installing adapters What to do next What to do next Installing internal drives Drive specifications User Guide Installing a drive in bay 1 or bay Installing a hard disk drive in bay Installing options Connecting drives Connecting the first optical drive Connecting a serial ATA hard disk drive Installing security features Padlock Password protectionChanging the battery Erasing a lost or forgotten password clearing Cmos Replacing the cover and connecting the cables Using the Setup Utility program Selecting a startup device Setting, changing, and deleting a passwordUsing Security Profile by Device Changing the startup sequence Exiting from the Setup Utility programSelecting a temporary startup device User Guide Appendix A. Updating system programs Updating flashing Bios from a diskette or CD-ROMUpdating flashing Bios from your operating system System programs Recovering from a POST/BIOS update failure Cleaning a mouse with a ball Appendix B. Cleaning the mouseCleaning an optical mouse User Guide Appendix C. Manual modem commands Basic AT commands Set Tone Dial as default Low speaker volumeSet Pulse dial as default Internal speaker on until carrier detected Extended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 1 commands Fax Class 2 commands Voice commands Appendix C. Manual modem commands User Guide Appendix D. Notices Television output notice Trademarks Index Sata connectors Page Part Number 39J7678