Manuals / LevelOne / Computer Equipment / Printer

LevelOne FPS-2112, FPS-3001TXU, FPS-3002USB manual TCP/IP Tab, TCP/IP Screen

Models: FPS-2112 FPS-3002USB FPS-3001TXU

1 95

Download 95 pages 59.88 Kb

Page 33

Level One Printer Servers

TCP/IP Tab

Selecting this tab will allow configuration for the TCP/IP network protocol. The basic options are:

•Dynamic IP Address (DHCP) - The IP address is obtained automatically, from a DHCP Server on your network.

•Fixed IP Address - You must enter the IP address, Subnet Mask, and Gateway Address.

•IP Address - Select an unused IP address from the address range used on your LAN.

•Subnet Mask - Use the same values as PCs on your LAN (or on the same LAN segment, if you have a Router).

•Gateway - Use the same values as PCs on your LAN (or on the same LAN segment, if you have a Router).

Some LevelOne Printer Server models also support the Auto-IP function. If the LevelOne Printer Server is set to Dynamic IP Address, but there's no DHCP server found on the network, the LevelOne Printer Server will get an IP from the range of 169.254.1.1 ~ 169.254.254.254 automatically. In this case, even though the LevelOne Printer Server was initialized with an Auto-IP, it will change to DHCP whenever a DHCP server is detected.

Figure 25: TCP/IP Screen

The TCP session parameters should only be changed if advised to do so by your Network Administrator or LevelOne Printer Server Technical Support.

- 30 -

Image 33

LevelOne FPS-2112, FPS-3001TXU, FPS-3002USB manual TCP/IP Tab, TCP/IP Screen

Contents

Level One Print Servers Table of Contents Appendix B Windows Server Configuration Appendix a SpecificationsAppendix C Unix Systems Appendix D NetWareIntroduction FeaturesPackage Contents Safety InstructionsPower Green Status Orange Description LED IndicatorsModels FPS-3001TXU 100BaseT Direct AttachFPS-3002USB Power Green Status Red DescriptionFPS-2112 Status DescriptionGreen Red Diagnostic Push Buttonfor FPS-3001TXU and FPS-3002USB To restore the factory default settingsTo generate a Diagnostic print out Procedure LAN InstallationUsing the Windows Wizard ConfigurationProcedure OverviewLevelOne Printer Server Screen If the desired LevelOne Printer Server is not listedClient PC Configuration Printing MethodsWhich printing method should I use? Checking your Network Protocols Windows Network ConfigurationWindows Peer-to-peer Printing Windows 2000/XP SetupChoose Standard TCP/IP Port, then click New Port Ensure the LPR Byte Counting Enabled setting is Enabled PTP Printer Port Setup Windows 9x/ME SetupIf your LevelOne Printer Server is not listed Print Port Setup Peer-to-peer PrintingManagement Configure Printer PortPort Advanced Port OptionsBanner Retry IntervalNetwork Neighborhood Windows SMB PrintingPrinting from MS-DOS Programs Capture Settings Windows 98/MELogin as Administrator Open the command prompt window Capture Settings Windows 2000/XPWindows with Server-based Print Queues When prompted for Network Path or Queue NameAdvanced Setup and Management AppleTalk SetupMacintosh AppleTalk Software RequirementsMacintosh OS LPR printing SetupInstallation BiAdmin Management UtilityRequirements OperationDevice List Icons Device StatusPrinter Status Upgrade ConfigurationWizard RefreshDiagnostics menu ConfigurationMenus Main MenuSystem Screen System TabTCP/IP Screen TCP/IP TabAppleTalk Screen AppleTalk TabNetBEUI Screen NetBEUI TabInternet Printing Screen Internet Printing TabPort Tab Physical PortLogical Port NetWare Tab Preparation Web-Based ManagementConnecting to the LevelOne Printer Server Configuration ScreensAppleTalk NetBEUI Abort Job if ErrorDomain Name Response TimeConnection General NetWareManagement Stations Snmp Simple Network Management ProtocolOther Screens Configure ServerServer Status Printer PortsInternet Printing Logical PrintersSpecial Features IPP Server ConfigurationInternet Printing Protocol IPP Installing from the CD-ROM IPP Client Setup Windows 98/MEInstalling using IPPCLIENT.EXE IPP Client ConfigurationSelect Printer for IPP Port Changing the IPP Port SettingsPort 2 if exists IPP Client Setup Windows 2000/XPUsing IPP Printers System Requirements Internet Mail PrintingMail Server Internet LevelOne Printer ServerInternet Mail Printing Configuration User Software Installation User SoftwarePort Name Remote PrinterChecking the Printer Driver Using the new PortInterNet Printing Progress Printing through the InternetHardware & LAN Problems TroubleshootingProblem No All the LevelOne Printer Servers LEDs are off If using 10/100BaseT, check the HubProblem No My document didnt print to the right printer Problem No Why do I get an incorrect printout?Problem No My file doesnt print with the correct fonts Problem No My EPS file doesnt print with the correct fontsLevel One Printer Servers Windows Printing To remove an existing printer port installationLevel One Printer Servers Problem No Then select File Properties Details Problem No My old printer cannot print or prints garbageLevelOne Printer Server device is not recognized Unix TroubleshootingEnvironmental Specifications SpecificationsFCC Statement CE StandardsACK Parallel Port Pin AssignmentsFPS-3002USB FPS-3002USBFPS-2112 FPS-2112Feature Table Specifications3001TXU 3002USB Windows NT4.0 Server Windows Server ConfigurationAdding TCP/IP Printing Support Adding a TCP/IP Remote PrinterWindows 2000 Message Windows 2000/2003 ServerLevelOne Printer Server IP Address Configuration Other LevelOne Printer Server ConfigurationUnix Systems LPD Printing LPD on IBM AIXField Entry Action Sample Command ProcedureLPD on System Adding Remote PrintersField Data LPD on LinuxLPD on BSD Printing using LPD NetWare NetWareCreating an Ndps Manager Object At the Identification page, click the Printer Agent List Creating an Ndps Printer AgentConfigure Port Handler Operation Mode NetWare 3Frame Type NetWare Remote Printer Mode NetWare Print Server ModeDevice Name Print ServerPreparation Using BiAdmin with ClientButtons Print Server Mode BinderyNetWare Configuration Button Bindery Quickset Button BinderyIf you have multiple File Servers File Server If you have a single File ServerPrinter OperatorSelect Printer Port Bindery Printer ButtonAssign Queues Bindery Assigning Printer Queues RequiredTo assign operators to Queues Optional To Assign Users to Queues RequiredNetWare Password Bindery PS Mode PasswordName Print Server Mode NDSQuickset Button NDS NetWare Configuration Button NDSSelect Printer Port NDS To assign operators to the Print Queue Optional Assign Users to Queue NDS PS modeNetWare Password NDS PS Mode Password NDS