SURFACE CONTROLS COOKING
English
Español
CAUTION
BEFORE SURFACE COOK
•Do not use the glass cooktop surface as a cutting board.•Do not place or store items that can melt or catch fire on the glass cooktop, even when it is not being used.
•Always turn the surface units on after placing cookware.•Do not store heavy items above the cooktop surface that could fall and damage it.
DURING SURFACE COOK
•Do not place aluminum foil or plastic items such as salt and pepper shakers, spoon holders, or plastic wrappings on the range when it is in use. The hot air from the vent could melt plastics or ignite flammable items
•Make sure you turned on the correct surface unit.•Never cook directly on the glass. Always use cookware.•Always place the pan in the center of the surface unit you are cooking on.•Never leave surface units unattended at high heat setting. Boilovers cause smoking and greasy spillovers that may catch on fire.
•Always turn the surface units off before removing cookware.•Do not use plastic wrap to cover food. Plastic may melt onto the surface and be very difficult to remove.
AFTER SURFACE COOK
•Do not touch surface units until it has cooled down.•The surface elements may still be hot and burns may occur if the glass surface is touched before it has cooled down sufficiently.
•Immediately clean the spills on cooking area to prevent a tough cleaning chore later.
•If cabinet storage is provided directly above cooking surface, limit it to items that are infrequently used and can be safely stored in an area subjected to heat. Temperatures may be unsafe for items such as volatile liquids, cleaners or aerosol sprays.
HS( Hot Surface) MESSAGE LIGHT WILL:
•Come on when the unit is hot to touch after it is turned off.•Come on during Self Cleaning Cycle.•Stay on even after the unit is turned off.•Glow until the unit has cooled down to approximately 150°F.LOCATIONS OF THE RADIANT SURFACE ELEMENTS AND CONTROLS
The radiant surface elements are located on the cooktop as below.The radiant control key locations are correlative to radiant surface elements on the cooktop as shown below.
| Single |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Single | |||||||||||||||
Left Rear Element | Warming Zone |
| Right Rear Element | ||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PF(Power Failure) MESSAGE
The PF message will appear whenever there has been a power interruption to the appliance. To clear the PF message press ON/OFF control pad to reset and be sure to reset the clock with the correct time of day.
Dual | Single |
Left Front | Right Front Element |
Dual Element |
|
- 6 -