LG Electronics PJ250R manual 113

MFL62883001-Edit3-en 3/17/10 3:47 PM Page 113

01. Power (Command: k a)				05. Volume Control (Command: k f)
To control Power On/Off of the TV.				To adjust volume.
				You can also adjust volume with the volume buttons
	Transmission [k][a][ ][Set ID][ ][Data][Cr]
				on remote control.
Data 00 : Power Off		Data 01 : Power On
					Transmission [k][f][ ][Set ID][ ][Data][Cr]
	Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]			Data Min : 00 ~ Max : 64
To show Power On/Off.				Refer to ‘Real data mapping 1 ’.
	Transmission [k][a][ ][Set ID][ ][FF][Cr]				Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
	Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* If there is the time delay between command and
	ack message during power on sequence, It should			06. Contrast (Command: k g)
	be described like “Note: In this model, TV will send			To adjust screen contrast.
	the Acknowledge after power on processing com-
				You can also adjust contrast in the PICTURE menu.
	pletion. There might be a time delay between com-
	mand and acknowledge.”
					Transmission [k][g][ ][Set ID][ ][Data][Cr]
				Data Min : 00 ~ Max : 64
02. Aspect Ratio (Command: k c) (Main picture size)				Refer to ‘Real data mapping 1’.
	To adjust the screen format. (Main picture format)				Acknowledgement [g][ ][Set ID][ ][OK][Data][x]
	You can adjust the screen format using the Aspect
	Ratio in the PICTURE menu.
	Transmission [k][c][ ][Set ID][ ][Data][Cr]			07. Brightness (Command: k h)
	Data 01: Normal screen (4:3)		Data 09: Just Scan
				To adjust screen brightness.
	Data 02: Wide screen (16:9)
				You can also adjust brightness in the PICTURE menu.
	Data 04: Zoom
	Data10~1F:CinemaZoom1~16
					Transmission [k][h][ ][Set ID][ ][Data][Cr]
	Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]			Data Min : 00 ~ Max : 64
* Using the RGB-PC, Component or HDMI input, you				Refer to ‘Real data mapping 1’.
	select either 16:9 or 4:3 screen aspect ratio.				Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
	* In HDMI/Component (over 720p)mode, Just Scan
	is available.
03. Screen Mute (Command: k d)				08. Color (Command: k i)
To select screen mute on/off.
				To adjust the screen color.
	Transmission [k][d][ ][Set ID][ ][Data][Cr]			You can also adjust color in the PICTURE menu.
Data 00 : Screen mute off (Picture/Panel on)
					Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data 01 : Screen mute on (Panel off)
				Data Min : 00 ~ Max : 64
Data 10 : Video mute on (Picture Off)
				Refer to ‘Real data mapping 1’.
	Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]				Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
	In case of Video-Out mute on only, TV will display On
	Screen Display(OSD) But, In case of Screen Mute On, TV
	will not display OSD.			09. Tint (Command: k j)
04. Volume Mute (Command: k e)				To adjust the screen tint.
To control volume mute on/off.				You can also adjust tint in the PICTURE menu.
You can also adjust mute using the MUTE button on
					Transmission [k][j][ ][Set ID][ ][Data][Cr]
remote control.
				Data Red : 00 ~ Green : 64
	Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)				Refer to ‘Real data mapping 1’.
Data 01 : Volume mute off (Volume on)					Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x]
	Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]

APPENDIX

113