Liebert XDP160RA, XDP160RC, XDP160RM +

Liebert iCOM Control—Firmware Version XP1.00.010.STD

42

Figure 42 Liebert XDP Service Menu screen

4.10 Liebert iCOM Service Menu Screens

Service menus allow customized settings for site operations. Service Menu screens employ a coding

that begins with “S” and is followed by parameters and information, such as settings. Gaining access

to most Service Menus requires entering a password; the Service Menu password is 5010; see 4.3.3 -

Entering the Password for assistance.

The Liebert iCOM control firmware is being updated constantly. As a result, the Service Menu

parameters in this manual may be slightly different from what is shown on a cooling unit’s display.

Check www.liebert.com for the latest Liebert iCOM user manual updates.

Figure 43 Setpoints screen

SERVICE MENUS

to select parameter

to change level

to open requested menu

ESC

to unselect

to navigate

+

WELLNESS

SET

ALARMS

SERVICE

+/-

NETWORK

SET

UP

XDIO

°C / °F

% RH

SET

SETPOINTS

to confirm

for next/prev ious unit

then

to select parameter

to change parameter

PASSW ORD (Actual Level 0 )

Min Room Temperat ure Setpoint

Temperature Control T ype

Temperature Proportional B and

Temperature Integrat ion Tiime

Temperature Deriv ative

Dewpoint M argin

Minimum Control Point

Min Percent C ooling Setpoint

S101

S102

S103

S104

S105

S106

S107

S108

S109

S110

S111

????

60.0°F

Intelligent

7.0°F

min

sec

4.0°F

50.0°F

10%

UNIT 01

Contents

Main Page TABLE OF CONTENTS 4.0 LIEBERT ICOM CONTROLFIRMWARE VERSION XP1.00.010.STD. . . . . . . . . . . . . . . . . .26 Page FIGURES TABL ES IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Figure 1 Model number nomenclature R XD P 160 * Example: XDP160RA 4 A 1.0 PRODUCT DESCRIPTION 1.1 General Product Information Chilled Water 1.1.1 Product/System Description 1.1.2 Minimum Load 1.3 Equipment Handling 1.3.1 Handling the Liebert XDP While it is on Skid and Packaged 1.3.2 Unpacking the Liebert XDP 1.3.3 Removing the Unit from the Skid Using a Forklift 1.3.4 Removing the Unit from the Skid using Rigging 1.3.5 Moving the Liebert XDP Using Piano Jacks Equally Spaced 1.3.6 Removing the Unit from the Piano Jacks 2.0 I 2.1 Mechanical Considerations Floor Cutout Dimensions 2.1.1 Positioning the Liebert XDP Figure 7 Dimensions 2.2 Electrical Considerations Table 3 Unit piping outlet connection sizes, inches, OD Cu Model Pipe Connection Point 50/60 Hz ABCD XDP160 2-1/8 1-1/8 2-5/8 2-5/8 DPN001598 Pg. 3, Rev. 7 2.2.1 Connecting High-Voltage Cables Page Page Figure 14 Connecting the remote temperature/humidity sensors 302211 Rev. 2 2.2.3 DIP Switch and Jumper Settings for Remote Sensors Figure 16 Unit-to-unit networking connections 302211 Rev. 2 302211 Rev. 2 2.3 Field ConnectionsOptional for All Units UNIT DISPLAY (Rear View) DPN001598 Pg. 6, Rev. 7 2.4 Remote Sensor InstallationProper Placement 3.0 P 3.1 European Union Fluorinated Greenhouse Gas Requirements 3.2 Connection Sizes 3.2.1 Recommended Pipe Size 3.3 Liebert XDP Interconnection with Liebert XD Cooling Modules 3.4 Piping Installation Methods 3.4.1 Piping InstallationR-134a Pumped Circuit 3.4.2 Piping Mains 3.4.3 Bypass Flow Controller 7/8" (22mm) ID 4"(102mm) Piping 21 Figure 21 Bypass flow controller arrangement 3.5 Piping DetailsShutoff/Isolation Valves Liebert XDP 3.5.1 Evacuation and Leak CheckR-134a Pumped Circuit 3.5.2 Insulation 3.6 Filling the Pumped CircuitR-134a 3.6.1 Calculating Refrigerant ChargeExample 3.7 Checklist for Proper Installation 4.0 LIEBERT ICOM CONTROLFIRMWARE VERSION XP1.00.010.STD 4.1 Liebert iCOM Components and Functions ESC ? 4.2 Display Lamp Indicators ? ESC 4.3 Navigating Through the Liebert iCOM Display XDP 4.3.1 Accessing Menus and Settings Viewing Data 28.02.2012 15 :03 UNIT ON UNIT 1 Sensor A B Temp: 74F 72F Hum: 50% 50% Dew Pt: 55F 54F Liebert XDP 4.3.3 Entering the Password 4.4 Changing Liebert iCOMs Display Settings 4.5 Changing Operational Settings 4.6 Graphical Data Record 4.7 Liebert iCOM User Menu Icons and Legend Figure 29 Liebert iCOM User Menu icons ! XDIO ACTIVE ALARMS 1 2 39 6 SET 1234h Figure 30 Liebert XDP User Menu screen USER MENUS 4.8 Liebert iCOM User Menu Screens Spare Parts Event Log Page Page Page Page Page Page 4.9 Liebert iCOM Service Menu Icons and Legend C / F % RH SET NETWORK XDIO WELLNESS SERVICE + Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 5.0 START THE LIEBERT XDP WITH LIEBERT ICOM 5.1 Checklist for Liebert XDP Startup 5.2 Starting the Liebert XDP with Liebert iCOM Controller 6.0 ALARM DESCRIPTIONS AND SOLUTIONS 6.1 Alarm Descriptions Page 6.2 Warning Descriptions 6.3 System Shutdown Causes Unit Is Off By Refrig Sens Fail Unit Is Off By High CW Temp Unit Is Off By Pump Short Cycle 7.0 TROUBLESHOOTING Table 14 Troubleshooting the Liebert XDP Symptom Possible Cause Check or Remedy Troubleshooting 70 Table 14 Troubleshooting the Liebert XDP (continued) Symptom Possible Cause Check or Remedy 8.0 MAINTENANCE 8.1 Fluorinated Greenhouse Gas Requirements 9.0 SPECIFICATIONS Table 15 Liebert XDP160 specifications COMPLIANCE WITH EUROPEAN UNION DIRECTIVES Ensuring The High Availability Of Mission-Critical Data And Applications.