Liebherr 7084376 - 03 Putting into operation, Transferring the lower bearing elements

Putting into operation

4.1.4 Transferring the lower bearing elements

Fig. 6

uDraw the safety lock Fig. 6 (21).

uRemove the cover Fig. 6 (27).*

uFully retract the adjustable-height foot Fig. 6 (22).

uIf necessary, tip the appliance back a little with the assistance of a second person for removal of the bearing pin.

uPull out the bearing pin Fig. 6 (22) downwards and forwards. In so doing, pay attention to the hinge bush Fig. 6 (20).

uUnscrew the turn hinge Fig. 6 (23) (3 Torx 25) Fig. 6 (24).

uUnscrew the bearing part Fig. 6 (26)(1 Torx 25), Fig. 6 (28).

uCarefully lift off and transfer the cover Fig.6 (25) on the handle side.

uScrew the turn hinge Fig. 6 (23) firmly into place on the new hinge side, possibly using a cordless screwdriver (with 4 Nm).

uTip the appliance back a little again and re-insert the bearing pin Fig. 7 (22). The notch has to point forwards.

uPlace the cover Fig. 6 (27) on the opposite side.*

Fig. 7

CAUTION

Risk of injury if the door tips!

u The safety lock (21) has to engage with the turn hinge at the side so that the bearing pin and therefore the door are secured.

u

uSnap the safety lock (21) onto the turn hinge again.

uPut on the hinge bush Fig. 6 (20).

4.1.5 Transferring the handles

uDisengage the spring clip Fig. 8 (31) from the upper door and transfer it to the new hinge side.

uLift the stoppers Fig.8 (30) out of the door bearing bushes and transfer them.

Fig. 8

uDetach the door handles Fig. 8 (32), stoppers Fig. 8 (33) and pressure plates Fig. 8 (34) and transfer to the opposite side.

uWhen fitting the pressure plates at the opposite side, pay attention that they engage properly.

4.1.6 Fitting the lower door

u Place the lower door from above onto the lower bearing pin Fig. 6 (22).

u Close the door.

u Place the plastic cap Fig. 5 (10) back onto the middle turn hinge Fig. 5 (13).

u Place the middle bearing pin Fig. 5 (11) in the lower door, on the new hinge side, through the middle turn hinge Fig. 5 (13).

4.1.7 Fitting the upper door

uPlace the upper door on the middle bearing pin Fig. 5 (11).

uInsert the upper turn hinge Fig. 4 (3) in the door on the new hinge side.

uScrew the top turn hinge firmly into place (with 4 Nm).(2x Torx 25) Fig. 4 (4). Possibly make preliminary holes with a bradawl or use a cordless screwdriver.

uApply the cover Fig. 4 (1) and cover Fig. 4 (2) to the opposite side from the outside and snap them into place.

4.1.8 Aligning the doors

uIf necessary, align the doors to the appliance housing by way of the two oblong holes in the lower turn hinge Fig. 6 (23) and middle turn hinge Fig. 5 (13). To do so, unscrew the middle screw in the lower turn hinge Fig. 6 (23).

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough, the door may drop out. This may lead to severe injuries. What is more, the door may not close and therefore the appliance may fail to cool properly.

u Screw the turn hinges firmly into place with 4 Nm. u Check all of the screws and retighten if necessary.

5