Liebherr 7084376 - 03 Insertion into a row of kitchen units, Transporting the appliance

Putting into operation

4.2 Insertion into a row of kitchen units

(1)	Stack cabinet	(3)	Fig. 9
			Kitchen cabinet
(2)	Appliance	(4)	Wall

The appliance can be inserted into a row of kitchen units. To match the appliance Fig. 9 (2) to the height of the row of units, a suitable stack cabinet Fig.9 (1) can be fitted above the appliance. When inserting the appliance into a row of standard kitchen units (max. depth 580 mm), the appliance can be installed directly next to the kitchen unit Fig. 9 (3). The appliance door projects relative to the front of the kitchen unit by 34 mm at the side and by 50 mm in the middle of the appliance. It can be opened and closed perfectly as a result.

Important for the ventilation:

-At the back of the stack cabinet there has to be a ventilation duct of at least 50 mm depth throughout the width of the stack cabinet.

-The ventilation space under the ceiling has to be at least 300 cm2.

If the appliance is installed with the hinges next to a wall Fig. 9 (4), the distance between appliance and wall has to be at least 36 mm. This corresponds to the projection of the handle when the door is open.

4.3 Transporting the appliance

CAUTION

Risk of injury and danger of damage as a result of incorrect trans- port!

u Transport the appliance in a packed condition. u Transport the appliance upright.

u Do not transport the appliance without assistance.

4.4 Installing the appliance

In the event that the appliance is damaged, contact the supplier immediately before connecting to the mains.

The floor at the site must be flat and level.

Do not install the appliance in a location where it is exposed to direct radiation of the sun, next to a cooker, heater and similar. Always install the appliance directly against the wall.

Do not install the appliance without assistance.

Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m2 per 8 g of R 600a refrig- erant used in the appliance. If the room in which the appliance is installed is too small, a flammable gas-air mixture may form in the event of a leakage in the refrigeration circuit. The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance.

WARNING

Fire hazard due to dampness!

If live parts or the mains lead become damp this may cause short circuits.

u The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions.

WARNING

Fire hazard due to refrigerant!

The refrigerant R 600a is environmentally friendly but flammable. Escaping refrigerant may ignite.

u Do not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

u Do not place appliances emitting heat e.g. microwaves, toasters etc. on the appliance!

WARNING

Fire hazard and risk of damage due to blocked ventilation grille! u Always keep the ventilation grille free. Always ensure that the

appliance is properly ventilated.

u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because other- wise there will be vibratory noise!

u Remove the protective film from the outside of the appli- ance.*

NOTICE*

The stainless steel doors are provided with a high-quality surface coating and must not be treated using the accompanying care product.

Otherwise the surface coating will be affected.

u Wipe the coated door surfaces using a soft, clean cloth only. u Apply a stainless steel cleaner only to the stainless steel side walls evenly, wiping with the grain. Subsequent cleaning

becomes easier as a result.

u Wipe side walls with a paint finish using a soft, clean cloth only.

u Remove the protective film from the decorative trims and drawer fronts.*

u Remove all transit supports.

u Dispose of packaging material (see 4.5) .

NOTICE

Risk of damage due to condensate!

u Do not install the appliance directly alongside a further refrig- erator/freezer.

u Align the appliance so that it stands firmly and on a level by applying the accompanying spanner to the adjustable- height feet (A) and using a spirit level.

u Then support the door: Extend the adjustable foot at the turn hinge (B) until it rests on the floor and then make a further 90° turn.

6