Manuals / Lincoln / Kitchen Appliance / Convection Oven

Lincoln 1100ADVSVC, 1117-000-A service manual Heating Element - Replacement, Bearing, Conveyor

Models: 1117-000-A 1100ADVSVC

1 36

Download 36 pages 40.03 Kb

Page 24

Image 24

HEATING ELEMENT - REPLACEMENT

1.Shut off power at main breaker.

2.Remove back cover.

3.Disconnect heater element wires and mark for reassembly.

4.Disconnect motor wiring and mark for reassembly.

5.Remove oven back from oven.

6.Remove fan shroud.

7.Heater element may now be unbolted and removed.

8.Check heater elements to be sure they ar the proper replacement.

9.Reassemble in reverse order. Apply anti-seize compound to back bolt threads before reassembly.

NOTE: Be sure the lead terminals are tight. If the leads are not tight, a loose connection will result, causing arcing and lead wire burn off.

BEARING, CONVEYOR

1.Remove conveyor from oven and place on a flat work surface.

2.Remove connecting links from conveyor belting.

3.Move drive shaft or idle shaft toward end of conveyor, and shaft with bearing will now slip out of holding bracket.

4.Replace bearing and reassemble.

24	Impinger II – Advantage Service Manual - Domestic

Page 24

Image 24

Lincoln 1100ADVSVC, 1117-000-A service manual Heating Element - Replacement, Bearing, Conveyor

Contents

Lincoln Foodservice Products, LLC Technical Service Hot Line1111 North Hadley Road Fort Wayne, Indiana United States of America Phone : 800TABLE OF CONTENTS SEQUENCE OF OPERATIONS IMPINGER II ADVANTAGE1130-000-A /208V / SINGLE PHASE SEQUENCE OF OPERATIONSSCHEMATIC 1116-000-A, 1117-000-A SCHEMATIC 1130-000-A / 1131-000-A SCHEMATIC 1132-000-A / 1133-000-A TROUBLESHOOTING GUIDE / GAS OVENS SYMPTOMPOSSIBLE CAUSE EVALUATIONAlso, WITH POWER OFF check for locked rotor VAC is not present, trace wiring back to Main FanCentrifugal Switch of Burner Check of 120 VAC at motor connector, on wire #13Power Supply VAC power supplyTemperature Control to neutral on temperature control. If no voltageSpeed Adjustment power off, remove the black and white pot leadsterminals L1 and L2. If not present, check wiring Power Supplyto the oven power source. Measure the secondary temperature displayTemp. display inoperative Display TransformerTROUBLESHOOTING GUIDE / ELECTRIC OVENS SYMPTOMPOSSIBLE CAUSE EVALUATIONTemperature Control thermostat. Turn the temperature adjustment knobto maximum temperature position and check for WITH POWER ON AND THERMOCOUPLESpeed Adjustment power off, remove the black and white pot leadsterminals L1 and L2. If not present, check wiring Power Supplywiring and connections for damage. check all power source. Measure the secondary outputTemperature Display on temperature display, but the display is notREMOVAL, INSTALLATION, AND ADJUSTMENT ON/OFF SWITCH - REPLACEMENTMOTOR, MAIN FAN FAN, MAINFUSE HOLDER - REPLACEMENT THERMOSTAT, CONTROL BOX HI-LIMIT- REPLACEMENTBURNER BLOWER MOTOR - REPLACEMENT HIGH LIMIT THERMOSTAT - REPLACEMENTBURNER TRANSFORMER - REPLACEMENT THERMOCOUPLE - REPLACEMENTTHERMOCOUPLE MEASUREMENT CHART TEMPERATURE CONTROL POTENTIOMETER - REPLACEMENT HEAT LIGHT - REPLACEMENTBURNER CONTROL - HONEYWELL - REPLACEMENT GAS VALVE - REPLACEMENTTEMPERATURE REGULATION VALVE - REPLACEMENT HOT SURFACE IGNITOR - REPLACEMENTMAIN BURNER ORIFICE - REPLACEMENT CONVEYOR CONTROL POTENTIOMETER - REPLACEMENTCONVEYOR CONTROL BOARD - REPLACEMENT CONVEYOR DRIVE MOTOR - REPLACEMENTCONVEYOR CONTROL BOARD - CALIBRATION CIRCUIT BREAKERHALL EFFECT SENSOR - REPLACEMENT TEMPERATURE DISPLAY TRANSFORMER - REPLACEMENTTEMPERATURE DISPLAY - REPLACEMENT CALIBRATION OF TEMPERATURE DISPLAYHEATING ELEMENT - REPLACEMENT BEARING, CONVEYORThis page intentionally left blank PARTS / GENERAL LETTERPART NUMBER DESCRIPTIONBLOW UP / GENERAL PARTS / CONTROL BOX 1116-000-A, 1117-000-A LETTERPART NUMBER DESCRIPTIONBLOW UP / CONTROL BOX - 1116-000-A, 1117-000-A PARTS / CONTROL BOX - 1130-000-ATHRU 1133-000-A LETTERPART NUMBER DESCRIPTIONBLOW UP / CONTROL BOX - 1130-000-ATHRU 1133-000-A PARTS / CONVEYOR & DOOR LETTERPART NUMBER DESCRIPTIONBLOW UP / CONVEYOR & DOOR PARTS / OVEN BACK ASSEMBLY LETTERPART NUMBER DESCRIPTIONBLOW UP / OVEN BACK ASSEMBLY