Manuals / Lincoln / Kitchen Appliance / Convection Oven

Lincoln 116-000-A service manual Lincoln Foodservice Products, LLC, Service Manual, Domestic

Models: 1117-000-A 1132-000-A 1130-000-A 1131-000-A 116-000-A 1133-000-A

1 32

Download 32 pages 25.41 Kb

Page 1

Image 1

SERVICE MANUAL

(DOMESTIC)

IMPINGER ADVANTAGE DIGITAL SERIES

MODEL 1116-000-A, 1117-000-A,

1130-000-A, 1131-000-A, 1132-000-A, 1133-000-A

WITH PUSH BUTTON CONTROLS

Lincoln Foodservice Products, LLC

1111 North Hadley Road

Fort Wayne, Indiana 46804

United States of America

Phone : (800) 374-3004

U.S. Fax: (888) 790-8193 • Int’l Fax: (260) 436-0735

Technical Service Hot Line

(800) 678-9511

www.lincolnfp.com

1100AdvDigSvc

REV: 3/20/08

Page 1

Image 1

Lincoln 116-000-A service manual Lincoln Foodservice Products, LLC, North Hadley Road Fort Wayne, Indiana, Service Manual

Contents

1111 North Hadley Road Fort Wayne, Indiana Lincoln Foodservice Products, LLCUnited States of America Phone : 800 U.S. Fax: 888 790-8193• Int’l Fax: 260SEQUENCE OF OPERATION IMPINGER II ADVANTAGE 1130-000-A SEQUENCE OF OPERATION IMPINGER II ADVANTAGESCHEMATIC DIAGRAM SERIAL NUMBER 2038616 AND ABOVE SCHEMATIC DIAGRAM MODEL 1130-000-A, 1131-000-ASERIAL NUMBER 2038616 AND ABOVE SCHEMATIC DIAGRAM MODEL 1132-000-A, 1133-000-ATROUBLESHOOTING GUIDE GAS OVENS Check for 120VAC at wire #5 input to centrifugal Centrifugal switch of main fanswitch, located at 6-pinconnector in raceway near present, trace wiring back to the main powerignition control, turn off the power switch for control will shut off and lock out. To reset thethe temperature control to the lowest setting Power supplyWITH POWER ON AND THERMOCOUPLE the oven control indicates a temperature readingto the thermocouple chart located in the 120VAC output to the temperature regulationtrace wiring back to the primary of the control at wire #14 to neutral. If no voltage is presentWITH POWER OFF: Check the motor windings as discharge before testingTROUBLESHOOTING GUIDE ELECTRIC OVENS exceeding temperature setting, check for proper for maximum oven temperature, and oven is notis present, trace wiring back to control control to maximum temperature see installationproper load. Check the specification plate for Check the Amp draw on each power leg forWITH POWER OFF: To check resistance of the Oven heats with switch offSwitch, conveyor reversing discharge before testingCheck continuity between switch terminals Replace switch as neededIMPINGER II ADVANTAGE SERIES REMOVAL, INSTALLATION AND ADJUSTMENTSA.Shut off power at main breaker FUSE HOLDER – REPLACEMENTTHERMOSTAT, CONTROL BOX HI-LIMIT– REPLACEMENT A.Shut off power at main breakerSee “TRANSFORMER –BURNER- REPLACEMENT TRANSFORMER, BURNER – REPLACEMENTA.Shut off power at main breaker BURNER CONTROL – REPLACEMENTGAS VALVE – REPLACEMENT A.Shut off power at main breakerA.Shut off power at main breaker BYPASS ORIFICE – REPLACEMENTMAIN BURNER ORIFICE – REPLACEMENT A.Shut off power at main breakerA.Shut off power at main breaker AIR PRESSURE SWITCH – REPLACEMENTD.Disconnect air tube from air pressure switch BEARING, CONVEYOR – REPLACEMENTGENERAL VIEW IMPINGER II ADVANTAGEPage CONTROL BOX MODEL 1116-000-A, 1117-000-A Page OVENS WITH PUSH BUTTON CONTROLS CONTROL BOXSERIAL NUMBER 2038616 AND ABOVE Page OVEN BACK ASSEMBLY Page CONVEYOR / DOOR